FILE
digi_acceleport.c
File preview with syntax highlighting.
linux-6.19.14/drivers/usb/serial/digi_acceleport.c
1// SPDX-License-Identifier: GPL-2.0+ 2/* 3* Digi AccelePort USB-4 and USB-2 Serial Converters 4* 5* Copyright 2000 by Digi International 6* 7* Shamelessly based on Brian Warner's keyspan_pda.c and Greg Kroah-Hartman's 8* usb-serial driver. 9* 10* Peter Berger (pberger@brimson.com) 11* Al Borchers (borchers@steinerpoint.com) 12*/ 13 14#include <linux/kernel.h> 15#include <linux/errno.h> 16#include <linux/slab.h> 17#include <linux/tty.h> 18#include <linux/tty_driver.h> 19#include <linux/tty_flip.h> 20#include <linux/module.h> 21#include <linux/spinlock.h> 22#include <linux/uaccess.h> 23#include <linux/usb.h> 24#include <linux/wait.h> 25#include <linux/sched/signal.h> 26#include <linux/usb/serial.h> 27 28/* Defines */ 29 30#define DRIVER_AUTHOR "Peter Berger <pberger@brimson.com>, Al Borchers <borchers@steinerpoint.com>" 31#define DRIVER_DESC "Digi AccelePort USB-2/USB-4 Serial Converter driver" 32 33/* port output buffer length -- must be <= transfer buffer length - 2 */ 34/* so we can be sure to send the full buffer in one urb */ 35#define DIGI_OUT_BUF_SIZE 8 36 37/* port input buffer length -- must be >= transfer buffer length - 3 */ 38/* so we can be sure to hold at least one full buffer from one urb */ 39#define DIGI_IN_BUF_SIZE 64 40 41/* retry timeout while sleeping */ 42#define DIGI_RETRY_TIMEOUT (HZ/10) 43 44/* timeout while waiting for tty output to drain in close */ 45/* this delay is used twice in close, so the total delay could */ 46/* be twice this value */ 47#define DIGI_CLOSE_TIMEOUT (5*HZ) 48 49 50/* AccelePort USB Defines */ 51 52/* ids */ 53#define DIGI_VENDOR_ID 0x05c5 54#define DIGI_2_ID 0x0002 /* USB-2 */ 55#define DIGI_4_ID 0x0004 /* USB-4 */ 56 57/* commands 58 * "INB": can be used on the in-band endpoint 59 * "OOB": can be used on the out-of-band endpoint 60 */ 61#define DIGI_CMD_SET_BAUD_RATE 0 /* INB, OOB */ 62#define DIGI_CMD_SET_WORD_SIZE 1 /* INB, OOB */ 63#define DIGI_CMD_SET_PARITY 2 /* INB, OOB */ 64#define DIGI_CMD_SET_STOP_BITS 3 /* INB, OOB */ 65#define DIGI_CMD_SET_INPUT_FLOW_CONTROL 4 /* INB, OOB */ 66#define DIGI_CMD_SET_OUTPUT_FLOW_CONTROL 5 /* INB, OOB */ 67#define DIGI_CMD_SET_DTR_SIGNAL 6 /* INB, OOB */ 68#define DIGI_CMD_SET_RTS_SIGNAL 7 /* INB, OOB */ 69#define DIGI_CMD_READ_INPUT_SIGNALS 8 /* OOB */ 70#define DIGI_CMD_IFLUSH_FIFO 9 /* OOB */ 71#define DIGI_CMD_RECEIVE_ENABLE 10 /* INB, OOB */ 72#define DIGI_CMD_BREAK_CONTROL 11 /* INB, OOB */ 73#define DIGI_CMD_LOCAL_LOOPBACK 12 /* INB, OOB */ 74#define DIGI_CMD_TRANSMIT_IDLE 13 /* INB, OOB */ 75#define DIGI_CMD_READ_UART_REGISTER 14 /* OOB */ 76#define DIGI_CMD_WRITE_UART_REGISTER 15 /* INB, OOB */ 77#define DIGI_CMD_AND_UART_REGISTER 16 /* INB, OOB */ 78#define DIGI_CMD_OR_UART_REGISTER 17 /* INB, OOB */ 79#define DIGI_CMD_SEND_DATA 18 /* INB */ 80#define DIGI_CMD_RECEIVE_DATA 19 /* INB */ 81#define DIGI_CMD_RECEIVE_DISABLE 20 /* INB */ 82#define DIGI_CMD_GET_PORT_TYPE 21 /* OOB */ 83 84/* baud rates */ 85#define DIGI_BAUD_50 0 86#define DIGI_BAUD_75 1 87#define DIGI_BAUD_110 2 88#define DIGI_BAUD_150 3 89#define DIGI_BAUD_200 4 90#define DIGI_BAUD_300 5 91#define DIGI_BAUD_600 6 92#define DIGI_BAUD_1200 7 93#define DIGI_BAUD_1800 8 94#define DIGI_BAUD_2400 9 95#define DIGI_BAUD_4800 10 96#define DIGI_BAUD_7200 11 97#define DIGI_BAUD_9600 12 98#define DIGI_BAUD_14400 13 99#define DIGI_BAUD_19200 14 100#define DIGI_BAUD_28800 15 101#define DIGI_BAUD_38400 16 102#define DIGI_BAUD_57600 17 103#define DIGI_BAUD_76800 18 104#define DIGI_BAUD_115200 19 105#define DIGI_BAUD_153600 20 106#define DIGI_BAUD_230400 21 107#define DIGI_BAUD_460800 22 108 109/* arguments */ 110#define DIGI_WORD_SIZE_5 0 111#define DIGI_WORD_SIZE_6 1 112#define DIGI_WORD_SIZE_7 2 113#define DIGI_WORD_SIZE_8 3 114 115#define DIGI_PARITY_NONE 0 116#define DIGI_PARITY_ODD 1 117#define DIGI_PARITY_EVEN 2 118#define DIGI_PARITY_MARK 3 119#define DIGI_PARITY_SPACE 4 120 121#define DIGI_STOP_BITS_1 0 122#define DIGI_STOP_BITS_2 1 123 124#define DIGI_INPUT_FLOW_CONTROL_XON_XOFF 1 125#define DIGI_INPUT_FLOW_CONTROL_RTS 2 126#define DIGI_INPUT_FLOW_CONTROL_DTR 4 127 128#define DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF 1 129#define DIGI_OUTPUT_FLOW_CONTROL_CTS 2 130#define DIGI_OUTPUT_FLOW_CONTROL_DSR 4 131 132#define DIGI_DTR_INACTIVE 0 133#define DIGI_DTR_ACTIVE 1 134#define DIGI_DTR_INPUT_FLOW_CONTROL 2 135 136#define DIGI_RTS_INACTIVE 0 137#define DIGI_RTS_ACTIVE 1 138#define DIGI_RTS_INPUT_FLOW_CONTROL 2 139#define DIGI_RTS_TOGGLE 3 140 141#define DIGI_FLUSH_TX 1 142#define DIGI_FLUSH_RX 2 143#define DIGI_RESUME_TX 4 /* clears xoff condition */ 144 145#define DIGI_TRANSMIT_NOT_IDLE 0 146#define DIGI_TRANSMIT_IDLE 1 147 148#define DIGI_DISABLE 0 149#define DIGI_ENABLE 1 150 151#define DIGI_DEASSERT 0 152#define DIGI_ASSERT 1 153 154/* in band status codes */ 155#define DIGI_OVERRUN_ERROR 4 156#define DIGI_PARITY_ERROR 8 157#define DIGI_FRAMING_ERROR 16 158#define DIGI_BREAK_ERROR 32 159 160/* out of band status */ 161#define DIGI_NO_ERROR 0 162#define DIGI_BAD_FIRST_PARAMETER 1 163#define DIGI_BAD_SECOND_PARAMETER 2 164#define DIGI_INVALID_LINE 3 165#define DIGI_INVALID_OPCODE 4 166 167/* input signals */ 168#define DIGI_READ_INPUT_SIGNALS_SLOT 1 169#define DIGI_READ_INPUT_SIGNALS_ERR 2 170#define DIGI_READ_INPUT_SIGNALS_BUSY 4 171#define DIGI_READ_INPUT_SIGNALS_PE 8 172#define DIGI_READ_INPUT_SIGNALS_CTS 16 173#define DIGI_READ_INPUT_SIGNALS_DSR 32 174#define DIGI_READ_INPUT_SIGNALS_RI 64 175#define DIGI_READ_INPUT_SIGNALS_DCD 128 176 177 178/* Structures */ 179 180struct digi_serial { 181 spinlock_t ds_serial_lock; 182 struct usb_serial_port *ds_oob_port; /* out-of-band port */ 183 int ds_oob_port_num; /* index of out-of-band port */ 184 int ds_device_started; 185}; 186 187struct digi_port { 188 spinlock_t dp_port_lock; 189 int dp_port_num; 190 int dp_out_buf_len; 191 unsigned char dp_out_buf[DIGI_OUT_BUF_SIZE]; 192 int dp_write_urb_in_use; 193 unsigned int dp_modem_signals; 194 int dp_transmit_idle; 195 wait_queue_head_t dp_transmit_idle_wait; 196 int dp_throttled; 197 int dp_throttle_restart; 198 wait_queue_head_t dp_flush_wait; 199 wait_queue_head_t dp_close_wait; /* wait queue for close */ 200 wait_queue_head_t write_wait; 201 struct usb_serial_port *dp_port; 202}; 203 204 205/* Local Function Declarations */ 206 207static int digi_write_oob_command(struct usb_serial_port *port, 208 unsigned char *buf, int count, int interruptible); 209static int digi_write_inb_command(struct usb_serial_port *port, 210 unsigned char *buf, int count, unsigned long timeout); 211static int digi_set_modem_signals(struct usb_serial_port *port, 212 unsigned int modem_signals, int interruptible); 213static int digi_transmit_idle(struct usb_serial_port *port, 214 unsigned long timeout); 215static void digi_rx_throttle(struct tty_struct *tty); 216static void digi_rx_unthrottle(struct tty_struct *tty); 217static void digi_set_termios(struct tty_struct *tty, 218 struct usb_serial_port *port, 219 const struct ktermios *old_termios); 220static int digi_break_ctl(struct tty_struct *tty, int break_state); 221static int digi_tiocmget(struct tty_struct *tty); 222static int digi_tiocmset(struct tty_struct *tty, unsigned int set, 223 unsigned int clear); 224static int digi_write(struct tty_struct *tty, struct usb_serial_port *port, 225 const unsigned char *buf, int count); 226static void digi_write_bulk_callback(struct urb *urb); 227static unsigned int digi_write_room(struct tty_struct *tty); 228static unsigned int digi_chars_in_buffer(struct tty_struct *tty); 229static int digi_open(struct tty_struct *tty, struct usb_serial_port *port); 230static void digi_close(struct usb_serial_port *port); 231static void digi_dtr_rts(struct usb_serial_port *port, int on); 232static int digi_startup_device(struct usb_serial *serial); 233static int digi_startup(struct usb_serial *serial); 234static void digi_disconnect(struct usb_serial *serial); 235static void digi_release(struct usb_serial *serial); 236static int digi_port_probe(struct usb_serial_port *port); 237static void digi_port_remove(struct usb_serial_port *port); 238static void digi_read_bulk_callback(struct urb *urb); 239static int digi_read_inb_callback(struct urb *urb); 240static int digi_read_oob_callback(struct urb *urb); 241 242 243static const struct usb_device_id id_table_combined[] = { 244 { USB_DEVICE(DIGI_VENDOR_ID, DIGI_2_ID) }, 245 { USB_DEVICE(DIGI_VENDOR_ID, DIGI_4_ID) }, 246 { } /* Terminating entry */ 247}; 248 249static const struct usb_device_id id_table_2[] = { 250 { USB_DEVICE(DIGI_VENDOR_ID, DIGI_2_ID) }, 251 { } /* Terminating entry */ 252}; 253 254static const struct usb_device_id id_table_4[] = { 255 { USB_DEVICE(DIGI_VENDOR_ID, DIGI_4_ID) }, 256 { } /* Terminating entry */ 257}; 258 259MODULE_DEVICE_TABLE(usb, id_table_combined); 260 261/* device info needed for the Digi serial converter */ 262 263static struct usb_serial_driver digi_acceleport_2_device = { 264 .driver = { 265 .name = "digi_2", 266 }, 267 .description = "Digi 2 port USB adapter", 268 .id_table = id_table_2, 269 .num_ports = 3, 270 .num_bulk_in = 4, 271 .num_bulk_out = 4, 272 .open = digi_open, 273 .close = digi_close, 274 .dtr_rts = digi_dtr_rts, 275 .write = digi_write, 276 .write_room = digi_write_room, 277 .write_bulk_callback = digi_write_bulk_callback, 278 .read_bulk_callback = digi_read_bulk_callback, 279 .chars_in_buffer = digi_chars_in_buffer, 280 .throttle = digi_rx_throttle, 281 .unthrottle = digi_rx_unthrottle, 282 .set_termios = digi_set_termios, 283 .break_ctl = digi_break_ctl, 284 .tiocmget = digi_tiocmget, 285 .tiocmset = digi_tiocmset, 286 .attach = digi_startup, 287 .disconnect = digi_disconnect, 288 .release = digi_release, 289 .port_probe = digi_port_probe, 290 .port_remove = digi_port_remove, 291}; 292 293static struct usb_serial_driver digi_acceleport_4_device = { 294 .driver = { 295 .name = "digi_4", 296 }, 297 .description = "Digi 4 port USB adapter", 298 .id_table = id_table_4, 299 .num_ports = 4, 300 .num_bulk_in = 5, 301 .num_bulk_out = 5, 302 .open = digi_open, 303 .close = digi_close, 304 .write = digi_write, 305 .write_room = digi_write_room, 306 .write_bulk_callback = digi_write_bulk_callback, 307 .read_bulk_callback = digi_read_bulk_callback, 308 .chars_in_buffer = digi_chars_in_buffer, 309 .throttle = digi_rx_throttle, 310 .unthrottle = digi_rx_unthrottle, 311 .set_termios = digi_set_termios, 312 .break_ctl = digi_break_ctl, 313 .tiocmget = digi_tiocmget, 314 .tiocmset = digi_tiocmset, 315 .attach = digi_startup, 316 .disconnect = digi_disconnect, 317 .release = digi_release, 318 .port_probe = digi_port_probe, 319 .port_remove = digi_port_remove, 320}; 321 322static struct usb_serial_driver * const serial_drivers[] = { 323 &digi_acceleport_2_device, &digi_acceleport_4_device, NULL 324}; 325 326/* Functions */ 327 328/* 329 * Cond Wait Interruptible Timeout Irqrestore 330 * 331 * Do spin_unlock_irqrestore and interruptible_sleep_on_timeout 332 * so that wake ups are not lost if they occur between the unlock 333 * and the sleep. In other words, spin_unlock_irqrestore and 334 * interruptible_sleep_on_timeout are "atomic" with respect to 335 * wake ups. This is used to implement condition variables. 336 * 337 * interruptible_sleep_on_timeout is deprecated and has been replaced 338 * with the equivalent code. 339 */ 340 341static long cond_wait_interruptible_timeout_irqrestore( 342 wait_queue_head_t *q, long timeout, 343 spinlock_t *lock, unsigned long flags) 344__releases(lock) 345{ 346 DEFINE_WAIT(wait); 347 348 prepare_to_wait(q, &wait, TASK_INTERRUPTIBLE); 349 spin_unlock_irqrestore(lock, flags); 350 timeout = schedule_timeout(timeout); 351 finish_wait(q, &wait); 352 353 return timeout; 354} 355 356/* 357 * Digi Write OOB Command 358 * 359 * Write commands on the out of band port. Commands are 4 360 * bytes each, multiple commands can be sent at once, and 361 * no command will be split across USB packets. Returns 0 362 * if successful, -EINTR if interrupted while sleeping and 363 * the interruptible flag is true, or a negative error 364 * returned by usb_submit_urb. 365 */ 366 367static int digi_write_oob_command(struct usb_serial_port *port, 368 unsigned char *buf, int count, int interruptible) 369{ 370 int ret = 0; 371 int len; 372 struct usb_serial_port *oob_port = (struct usb_serial_port *)((struct digi_serial *)(usb_get_serial_data(port->serial)))->ds_oob_port; 373 struct digi_port *oob_priv = usb_get_serial_port_data(oob_port); 374 unsigned long flags; 375 376 dev_dbg(&port->dev, 377 "digi_write_oob_command: TOP: port=%d, count=%d\n", 378 oob_priv->dp_port_num, count); 379 380 spin_lock_irqsave(&oob_priv->dp_port_lock, flags); 381 while (count > 0) { 382 while (oob_priv->dp_write_urb_in_use) { 383 cond_wait_interruptible_timeout_irqrestore( 384 &oob_priv->write_wait, DIGI_RETRY_TIMEOUT, 385 &oob_priv->dp_port_lock, flags); 386 if (interruptible && signal_pending(current)) 387 return -EINTR; 388 spin_lock_irqsave(&oob_priv->dp_port_lock, flags); 389 } 390 391 /* len must be a multiple of 4, so commands are not split */ 392 len = min(count, oob_port->bulk_out_size); 393 if (len > 4) 394 len &= ~3; 395 memcpy(oob_port->write_urb->transfer_buffer, buf, len); 396 oob_port->write_urb->transfer_buffer_length = len; 397 ret = usb_submit_urb(oob_port->write_urb, GFP_ATOMIC); 398 if (ret == 0) { 399 oob_priv->dp_write_urb_in_use = 1; 400 count -= len; 401 buf += len; 402 } 403 } 404 spin_unlock_irqrestore(&oob_priv->dp_port_lock, flags); 405 if (ret) 406 dev_err(&port->dev, "%s: usb_submit_urb failed, ret=%d\n", 407 __func__, ret); 408 return ret; 409 410} 411 412 413/* 414 * Digi Write In Band Command 415 * 416 * Write commands on the given port. Commands are 4 417 * bytes each, multiple commands can be sent at once, and 418 * no command will be split across USB packets. If timeout 419 * is non-zero, write in band command will return after 420 * waiting unsuccessfully for the URB status to clear for 421 * timeout ticks. Returns 0 if successful, or a negative 422 * error returned by digi_write. 423 */ 424 425static int digi_write_inb_command(struct usb_serial_port *port, 426 unsigned char *buf, int count, unsigned long timeout) 427{ 428 int ret = 0; 429 int len; 430 struct digi_port *priv = usb_get_serial_port_data(port); 431 unsigned char *data = port->write_urb->transfer_buffer; 432 unsigned long flags; 433 434 dev_dbg(&port->dev, "digi_write_inb_command: TOP: port=%d, count=%d\n", 435 priv->dp_port_num, count); 436 437 if (timeout) 438 timeout += jiffies; 439 else 440 timeout = ULONG_MAX; 441 442 spin_lock_irqsave(&priv->dp_port_lock, flags); 443 while (count > 0 && ret == 0) { 444 while (priv->dp_write_urb_in_use && 445 time_before(jiffies, timeout)) { 446 cond_wait_interruptible_timeout_irqrestore( 447 &priv->write_wait, DIGI_RETRY_TIMEOUT, 448 &priv->dp_port_lock, flags); 449 if (signal_pending(current)) 450 return -EINTR; 451 spin_lock_irqsave(&priv->dp_port_lock, flags); 452 } 453 454 /* len must be a multiple of 4 and small enough to */ 455 /* guarantee the write will send buffered data first, */ 456 /* so commands are in order with data and not split */ 457 len = min(count, port->bulk_out_size-2-priv->dp_out_buf_len); 458 if (len > 4) 459 len &= ~3; 460 461 /* write any buffered data first */ 462 if (priv->dp_out_buf_len > 0) { 463 data[0] = DIGI_CMD_SEND_DATA; 464 data[1] = priv->dp_out_buf_len; 465 memcpy(data + 2, priv->dp_out_buf, 466 priv->dp_out_buf_len); 467 memcpy(data + 2 + priv->dp_out_buf_len, buf, len); 468 port->write_urb->transfer_buffer_length 469 = priv->dp_out_buf_len + 2 + len; 470 } else { 471 memcpy(data, buf, len); 472 port->write_urb->transfer_buffer_length = len; 473 } 474 475 ret = usb_submit_urb(port->write_urb, GFP_ATOMIC); 476 if (ret == 0) { 477 priv->dp_write_urb_in_use = 1; 478 priv->dp_out_buf_len = 0; 479 count -= len; 480 buf += len; 481 } 482 483 } 484 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 485 486 if (ret) 487 dev_err(&port->dev, 488 "%s: usb_submit_urb failed, ret=%d, port=%d\n", 489 __func__, ret, priv->dp_port_num); 490 return ret; 491} 492 493 494/* 495 * Digi Set Modem Signals 496 * 497 * Sets or clears DTR and RTS on the port, according to the 498 * modem_signals argument. Use TIOCM_DTR and TIOCM_RTS flags 499 * for the modem_signals argument. Returns 0 if successful, 500 * -EINTR if interrupted while sleeping, or a non-zero error 501 * returned by usb_submit_urb. 502 */ 503 504static int digi_set_modem_signals(struct usb_serial_port *port, 505 unsigned int modem_signals, int interruptible) 506{ 507 508 int ret; 509 struct digi_port *port_priv = usb_get_serial_port_data(port); 510 struct usb_serial_port *oob_port = (struct usb_serial_port *) ((struct digi_serial *)(usb_get_serial_data(port->serial)))->ds_oob_port; 511 struct digi_port *oob_priv = usb_get_serial_port_data(oob_port); 512 unsigned char *data = oob_port->write_urb->transfer_buffer; 513 unsigned long flags; 514 515 dev_dbg(&port->dev, 516 "digi_set_modem_signals: TOP: port=%d, modem_signals=0x%x\n", 517 port_priv->dp_port_num, modem_signals); 518 519 spin_lock_irqsave(&oob_priv->dp_port_lock, flags); 520 spin_lock(&port_priv->dp_port_lock); 521 522 while (oob_priv->dp_write_urb_in_use) { 523 spin_unlock(&port_priv->dp_port_lock); 524 cond_wait_interruptible_timeout_irqrestore( 525 &oob_priv->write_wait, DIGI_RETRY_TIMEOUT, 526 &oob_priv->dp_port_lock, flags); 527 if (interruptible && signal_pending(current)) 528 return -EINTR; 529 spin_lock_irqsave(&oob_priv->dp_port_lock, flags); 530 spin_lock(&port_priv->dp_port_lock); 531 } 532 data[0] = DIGI_CMD_SET_DTR_SIGNAL; 533 data[1] = port_priv->dp_port_num; 534 data[2] = (modem_signals & TIOCM_DTR) ? 535 DIGI_DTR_ACTIVE : DIGI_DTR_INACTIVE; 536 data[3] = 0; 537 data[4] = DIGI_CMD_SET_RTS_SIGNAL; 538 data[5] = port_priv->dp_port_num; 539 data[6] = (modem_signals & TIOCM_RTS) ? 540 DIGI_RTS_ACTIVE : DIGI_RTS_INACTIVE; 541 data[7] = 0; 542 543 oob_port->write_urb->transfer_buffer_length = 8; 544 545 ret = usb_submit_urb(oob_port->write_urb, GFP_ATOMIC); 546 if (ret == 0) { 547 oob_priv->dp_write_urb_in_use = 1; 548 port_priv->dp_modem_signals &= ~(TIOCM_DTR | TIOCM_RTS); 549 port_priv->dp_modem_signals |= 550 modem_signals & (TIOCM_DTR | TIOCM_RTS); 551 } 552 spin_unlock(&port_priv->dp_port_lock); 553 spin_unlock_irqrestore(&oob_priv->dp_port_lock, flags); 554 if (ret) 555 dev_err(&port->dev, "%s: usb_submit_urb failed, ret=%d\n", 556 __func__, ret); 557 return ret; 558} 559 560/* 561 * Digi Transmit Idle 562 * 563 * Digi transmit idle waits, up to timeout ticks, for the transmitter 564 * to go idle. It returns 0 if successful or a negative error. 565 * 566 * There are race conditions here if more than one process is calling 567 * digi_transmit_idle on the same port at the same time. However, this 568 * is only called from close, and only one process can be in close on a 569 * port at a time, so its ok. 570 */ 571 572static int digi_transmit_idle(struct usb_serial_port *port, 573 unsigned long timeout) 574{ 575 int ret; 576 unsigned char buf[2]; 577 struct digi_port *priv = usb_get_serial_port_data(port); 578 unsigned long flags; 579 580 spin_lock_irqsave(&priv->dp_port_lock, flags); 581 priv->dp_transmit_idle = 0; 582 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 583 584 buf[0] = DIGI_CMD_TRANSMIT_IDLE; 585 buf[1] = 0; 586 587 timeout += jiffies; 588 589 ret = digi_write_inb_command(port, buf, 2, timeout - jiffies); 590 if (ret != 0) 591 return ret; 592 593 spin_lock_irqsave(&priv->dp_port_lock, flags); 594 595 while (time_before(jiffies, timeout) && !priv->dp_transmit_idle) { 596 cond_wait_interruptible_timeout_irqrestore( 597 &priv->dp_transmit_idle_wait, DIGI_RETRY_TIMEOUT, 598 &priv->dp_port_lock, flags); 599 if (signal_pending(current)) 600 return -EINTR; 601 spin_lock_irqsave(&priv->dp_port_lock, flags); 602 } 603 priv->dp_transmit_idle = 0; 604 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 605 return 0; 606 607} 608 609 610static void digi_rx_throttle(struct tty_struct *tty) 611{ 612 unsigned long flags; 613 struct usb_serial_port *port = tty->driver_data; 614 struct digi_port *priv = usb_get_serial_port_data(port); 615 616 /* stop receiving characters by not resubmitting the read urb */ 617 spin_lock_irqsave(&priv->dp_port_lock, flags); 618 priv->dp_throttled = 1; 619 priv->dp_throttle_restart = 0; 620 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 621} 622 623 624static void digi_rx_unthrottle(struct tty_struct *tty) 625{ 626 int ret = 0; 627 unsigned long flags; 628 struct usb_serial_port *port = tty->driver_data; 629 struct digi_port *priv = usb_get_serial_port_data(port); 630 631 spin_lock_irqsave(&priv->dp_port_lock, flags); 632 633 /* restart read chain */ 634 if (priv->dp_throttle_restart) 635 ret = usb_submit_urb(port->read_urb, GFP_ATOMIC); 636 637 /* turn throttle off */ 638 priv->dp_throttled = 0; 639 priv->dp_throttle_restart = 0; 640 641 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 642 643 if (ret) 644 dev_err(&port->dev, 645 "%s: usb_submit_urb failed, ret=%d, port=%d\n", 646 __func__, ret, priv->dp_port_num); 647} 648 649 650static void digi_set_termios(struct tty_struct *tty, 651 struct usb_serial_port *port, 652 const struct ktermios *old_termios) 653{ 654 struct digi_port *priv = usb_get_serial_port_data(port); 655 struct device *dev = &port->dev; 656 unsigned int iflag = tty->termios.c_iflag; 657 unsigned int cflag = tty->termios.c_cflag; 658 unsigned int old_iflag = old_termios->c_iflag; 659 unsigned int old_cflag = old_termios->c_cflag; 660 unsigned char buf[32]; 661 unsigned int modem_signals; 662 int arg, ret; 663 int i = 0; 664 speed_t baud; 665 666 dev_dbg(dev, 667 "digi_set_termios: TOP: port=%d, iflag=0x%x, old_iflag=0x%x, cflag=0x%x, old_cflag=0x%x\n", 668 priv->dp_port_num, iflag, old_iflag, cflag, old_cflag); 669 670 /* set baud rate */ 671 baud = tty_get_baud_rate(tty); 672 if (baud != tty_termios_baud_rate(old_termios)) { 673 arg = -1; 674 675 /* reassert DTR and (maybe) RTS on transition from B0 */ 676 if ((old_cflag & CBAUD) == B0) { 677 /* don't set RTS if using hardware flow control */ 678 /* and throttling input */ 679 modem_signals = TIOCM_DTR; 680 if (!C_CRTSCTS(tty) || !tty_throttled(tty)) 681 modem_signals |= TIOCM_RTS; 682 digi_set_modem_signals(port, modem_signals, 1); 683 } 684 switch (baud) { 685 /* drop DTR and RTS on transition to B0 */ 686 case 0: digi_set_modem_signals(port, 0, 1); break; 687 case 50: arg = DIGI_BAUD_50; break; 688 case 75: arg = DIGI_BAUD_75; break; 689 case 110: arg = DIGI_BAUD_110; break; 690 case 150: arg = DIGI_BAUD_150; break; 691 case 200: arg = DIGI_BAUD_200; break; 692 case 300: arg = DIGI_BAUD_300; break; 693 case 600: arg = DIGI_BAUD_600; break; 694 case 1200: arg = DIGI_BAUD_1200; break; 695 case 1800: arg = DIGI_BAUD_1800; break; 696 case 2400: arg = DIGI_BAUD_2400; break; 697 case 4800: arg = DIGI_BAUD_4800; break; 698 case 9600: arg = DIGI_BAUD_9600; break; 699 case 19200: arg = DIGI_BAUD_19200; break; 700 case 38400: arg = DIGI_BAUD_38400; break; 701 case 57600: arg = DIGI_BAUD_57600; break; 702 case 115200: arg = DIGI_BAUD_115200; break; 703 case 230400: arg = DIGI_BAUD_230400; break; 704 case 460800: arg = DIGI_BAUD_460800; break; 705 default: 706 arg = DIGI_BAUD_9600; 707 baud = 9600; 708 break; 709 } 710 if (arg != -1) { 711 buf[i++] = DIGI_CMD_SET_BAUD_RATE; 712 buf[i++] = priv->dp_port_num; 713 buf[i++] = arg; 714 buf[i++] = 0; 715 } 716 } 717 /* set parity */ 718 tty->termios.c_cflag &= ~CMSPAR; 719 720 if ((cflag & (PARENB | PARODD)) != (old_cflag & (PARENB | PARODD))) { 721 if (cflag & PARENB) { 722 if (cflag & PARODD) 723 arg = DIGI_PARITY_ODD; 724 else 725 arg = DIGI_PARITY_EVEN; 726 } else { 727 arg = DIGI_PARITY_NONE; 728 } 729 buf[i++] = DIGI_CMD_SET_PARITY; 730 buf[i++] = priv->dp_port_num; 731 buf[i++] = arg; 732 buf[i++] = 0; 733 } 734 /* set word size */ 735 if ((cflag & CSIZE) != (old_cflag & CSIZE)) { 736 arg = -1; 737 switch (cflag & CSIZE) { 738 case CS5: arg = DIGI_WORD_SIZE_5; break; 739 case CS6: arg = DIGI_WORD_SIZE_6; break; 740 case CS7: arg = DIGI_WORD_SIZE_7; break; 741 case CS8: arg = DIGI_WORD_SIZE_8; break; 742 default: 743 dev_dbg(dev, 744 "digi_set_termios: can't handle word size %d\n", 745 cflag & CSIZE); 746 break; 747 } 748 749 if (arg != -1) { 750 buf[i++] = DIGI_CMD_SET_WORD_SIZE; 751 buf[i++] = priv->dp_port_num; 752 buf[i++] = arg; 753 buf[i++] = 0; 754 } 755 756 } 757 758 /* set stop bits */ 759 if ((cflag & CSTOPB) != (old_cflag & CSTOPB)) { 760 761 if ((cflag & CSTOPB)) 762 arg = DIGI_STOP_BITS_2; 763 else 764 arg = DIGI_STOP_BITS_1; 765 766 buf[i++] = DIGI_CMD_SET_STOP_BITS; 767 buf[i++] = priv->dp_port_num; 768 buf[i++] = arg; 769 buf[i++] = 0; 770 771 } 772 773 /* set input flow control */ 774 if ((iflag & IXOFF) != (old_iflag & IXOFF) || 775 (cflag & CRTSCTS) != (old_cflag & CRTSCTS)) { 776 arg = 0; 777 if (iflag & IXOFF) 778 arg |= DIGI_INPUT_FLOW_CONTROL_XON_XOFF; 779 else 780 arg &= ~DIGI_INPUT_FLOW_CONTROL_XON_XOFF; 781 782 if (cflag & CRTSCTS) { 783 arg |= DIGI_INPUT_FLOW_CONTROL_RTS; 784 785 /* On USB-4 it is necessary to assert RTS prior */ 786 /* to selecting RTS input flow control. */ 787 buf[i++] = DIGI_CMD_SET_RTS_SIGNAL; 788 buf[i++] = priv->dp_port_num; 789 buf[i++] = DIGI_RTS_ACTIVE; 790 buf[i++] = 0; 791 792 } else { 793 arg &= ~DIGI_INPUT_FLOW_CONTROL_RTS; 794 } 795 buf[i++] = DIGI_CMD_SET_INPUT_FLOW_CONTROL; 796 buf[i++] = priv->dp_port_num; 797 buf[i++] = arg; 798 buf[i++] = 0; 799 } 800 801 /* set output flow control */ 802 if ((iflag & IXON) != (old_iflag & IXON) || 803 (cflag & CRTSCTS) != (old_cflag & CRTSCTS)) { 804 arg = 0; 805 if (iflag & IXON) 806 arg |= DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF; 807 else 808 arg &= ~DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF; 809 810 if (cflag & CRTSCTS) 811 arg |= DIGI_OUTPUT_FLOW_CONTROL_CTS; 812 else 813 arg &= ~DIGI_OUTPUT_FLOW_CONTROL_CTS; 814 815 buf[i++] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL; 816 buf[i++] = priv->dp_port_num; 817 buf[i++] = arg; 818 buf[i++] = 0; 819 } 820 821 /* set receive enable/disable */ 822 if ((cflag & CREAD) != (old_cflag & CREAD)) { 823 if (cflag & CREAD) 824 arg = DIGI_ENABLE; 825 else 826 arg = DIGI_DISABLE; 827 828 buf[i++] = DIGI_CMD_RECEIVE_ENABLE; 829 buf[i++] = priv->dp_port_num; 830 buf[i++] = arg; 831 buf[i++] = 0; 832 } 833 ret = digi_write_oob_command(port, buf, i, 1); 834 if (ret != 0) 835 dev_dbg(dev, "digi_set_termios: write oob failed, ret=%d\n", ret); 836 tty_encode_baud_rate(tty, baud, baud); 837} 838 839 840static int digi_break_ctl(struct tty_struct *tty, int break_state) 841{ 842 struct usb_serial_port *port = tty->driver_data; 843 unsigned char buf[4]; 844 845 buf[0] = DIGI_CMD_BREAK_CONTROL; 846 buf[1] = 2; /* length */ 847 buf[2] = break_state ? 1 : 0; 848 buf[3] = 0; /* pad */ 849 850 return digi_write_inb_command(port, buf, 4, 0); 851} 852 853 854static int digi_tiocmget(struct tty_struct *tty) 855{ 856 struct usb_serial_port *port = tty->driver_data; 857 struct digi_port *priv = usb_get_serial_port_data(port); 858 unsigned int val; 859 unsigned long flags; 860 861 spin_lock_irqsave(&priv->dp_port_lock, flags); 862 val = priv->dp_modem_signals; 863 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 864 return val; 865} 866 867 868static int digi_tiocmset(struct tty_struct *tty, 869 unsigned int set, unsigned int clear) 870{ 871 struct usb_serial_port *port = tty->driver_data; 872 struct digi_port *priv = usb_get_serial_port_data(port); 873 unsigned int val; 874 unsigned long flags; 875 876 spin_lock_irqsave(&priv->dp_port_lock, flags); 877 val = (priv->dp_modem_signals & ~clear) | set; 878 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 879 return digi_set_modem_signals(port, val, 1); 880} 881 882 883static int digi_write(struct tty_struct *tty, struct usb_serial_port *port, 884 const unsigned char *buf, int count) 885{ 886 887 int ret, data_len, new_len; 888 struct digi_port *priv = usb_get_serial_port_data(port); 889 unsigned char *data = port->write_urb->transfer_buffer; 890 unsigned long flags; 891 892 dev_dbg(&port->dev, "digi_write: TOP: port=%d, count=%d\n", 893 priv->dp_port_num, count); 894 895 /* copy user data (which can sleep) before getting spin lock */ 896 count = min(count, port->bulk_out_size-2); 897 count = min(64, count); 898 899 /* be sure only one write proceeds at a time */ 900 /* there are races on the port private buffer */ 901 spin_lock_irqsave(&priv->dp_port_lock, flags); 902 903 /* wait for urb status clear to submit another urb */ 904 if (priv->dp_write_urb_in_use) { 905 /* buffer data if count is 1 (probably put_char) if possible */ 906 if (count == 1 && priv->dp_out_buf_len < DIGI_OUT_BUF_SIZE) { 907 priv->dp_out_buf[priv->dp_out_buf_len++] = *buf; 908 new_len = 1; 909 } else { 910 new_len = 0; 911 } 912 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 913 return new_len; 914 } 915 916 /* allow space for any buffered data and for new data, up to */ 917 /* transfer buffer size - 2 (for command and length bytes) */ 918 new_len = min(count, port->bulk_out_size-2-priv->dp_out_buf_len); 919 data_len = new_len + priv->dp_out_buf_len; 920 921 if (data_len == 0) { 922 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 923 return 0; 924 } 925 926 port->write_urb->transfer_buffer_length = data_len+2; 927 928 *data++ = DIGI_CMD_SEND_DATA; 929 *data++ = data_len; 930 931 /* copy in buffered data first */ 932 memcpy(data, priv->dp_out_buf, priv->dp_out_buf_len); 933 data += priv->dp_out_buf_len; 934 935 /* copy in new data */ 936 memcpy(data, buf, new_len); 937 938 ret = usb_submit_urb(port->write_urb, GFP_ATOMIC); 939 if (ret == 0) { 940 priv->dp_write_urb_in_use = 1; 941 ret = new_len; 942 priv->dp_out_buf_len = 0; 943 } 944 945 /* return length of new data written, or error */ 946 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 947 if (ret < 0) 948 dev_err_console(port, 949 "%s: usb_submit_urb failed, ret=%d, port=%d\n", 950 __func__, ret, priv->dp_port_num); 951 dev_dbg(&port->dev, "digi_write: returning %d\n", ret); 952 return ret; 953 954} 955 956static void digi_write_bulk_callback(struct urb *urb) 957{ 958 959 struct usb_serial_port *port = urb->context; 960 struct usb_serial *serial; 961 struct digi_port *priv; 962 struct digi_serial *serial_priv; 963 unsigned long flags; 964 int ret = 0; 965 int status = urb->status; 966 bool wakeup; 967 968 /* port and serial sanity check */ 969 if (port == NULL || (priv = usb_get_serial_port_data(port)) == NULL) { 970 pr_err("%s: port or port->private is NULL, status=%d\n", 971 __func__, status); 972 return; 973 } 974 serial = port->serial; 975 if (serial == NULL || (serial_priv = usb_get_serial_data(serial)) == NULL) { 976 dev_err(&port->dev, 977 "%s: serial or serial->private is NULL, status=%d\n", 978 __func__, status); 979 return; 980 } 981 982 /* handle oob callback */ 983 if (priv->dp_port_num == serial_priv->ds_oob_port_num) { 984 dev_dbg(&port->dev, "digi_write_bulk_callback: oob callback\n"); 985 spin_lock_irqsave(&priv->dp_port_lock, flags); 986 priv->dp_write_urb_in_use = 0; 987 wake_up_interruptible(&priv->write_wait); 988 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 989 return; 990 } 991 992 /* try to send any buffered data on this port */ 993 wakeup = true; 994 spin_lock_irqsave(&priv->dp_port_lock, flags); 995 priv->dp_write_urb_in_use = 0; 996 if (priv->dp_out_buf_len > 0) { 997 *((unsigned char *)(port->write_urb->transfer_buffer)) 998 = (unsigned char)DIGI_CMD_SEND_DATA; 999 *((unsigned char *)(port->write_urb->transfer_buffer) + 1) 1000 = (unsigned char)priv->dp_out_buf_len; 1001 port->write_urb->transfer_buffer_length = 1002 priv->dp_out_buf_len + 2; 1003 memcpy(port->write_urb->transfer_buffer + 2, priv->dp_out_buf, 1004 priv->dp_out_buf_len); 1005 ret = usb_submit_urb(port->write_urb, GFP_ATOMIC); 1006 if (ret == 0) { 1007 priv->dp_write_urb_in_use = 1; 1008 priv->dp_out_buf_len = 0; 1009 wakeup = false; 1010 } 1011 } 1012 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 1013 1014 if (ret && ret != -EPERM) 1015 dev_err_console(port, 1016 "%s: usb_submit_urb failed, ret=%d, port=%d\n", 1017 __func__, ret, priv->dp_port_num); 1018 1019 if (wakeup) 1020 tty_port_tty_wakeup(&port->port); 1021} 1022 1023static unsigned int digi_write_room(struct tty_struct *tty) 1024{ 1025 struct usb_serial_port *port = tty->driver_data; 1026 struct digi_port *priv = usb_get_serial_port_data(port); 1027 unsigned long flags; 1028 unsigned int room; 1029 1030 spin_lock_irqsave(&priv->dp_port_lock, flags); 1031 1032 if (priv->dp_write_urb_in_use) 1033 room = 0; 1034 else 1035 room = port->bulk_out_size - 2 - priv->dp_out_buf_len; 1036 1037 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 1038 dev_dbg(&port->dev, "digi_write_room: port=%d, room=%u\n", priv->dp_port_num, room); 1039 return room; 1040 1041} 1042 1043static unsigned int digi_chars_in_buffer(struct tty_struct *tty) 1044{ 1045 struct usb_serial_port *port = tty->driver_data; 1046 struct digi_port *priv = usb_get_serial_port_data(port); 1047 unsigned long flags; 1048 unsigned int chars; 1049 1050 spin_lock_irqsave(&priv->dp_port_lock, flags); 1051 if (priv->dp_write_urb_in_use) 1052 chars = port->bulk_out_size - 2; 1053 else 1054 chars = priv->dp_out_buf_len; 1055 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 1056 1057 dev_dbg(&port->dev, "%s: port=%d, chars=%d\n", __func__, 1058 priv->dp_port_num, chars); 1059 return chars; 1060} 1061 1062static void digi_dtr_rts(struct usb_serial_port *port, int on) 1063{ 1064 /* Adjust DTR and RTS */ 1065 digi_set_modem_signals(port, on * (TIOCM_DTR | TIOCM_RTS), 1); 1066} 1067 1068static int digi_open(struct tty_struct *tty, struct usb_serial_port *port) 1069{ 1070 int ret; 1071 unsigned char buf[32]; 1072 struct digi_port *priv = usb_get_serial_port_data(port); 1073 struct ktermios not_termios; 1074 1075 /* be sure the device is started up */ 1076 if (digi_startup_device(port->serial) != 0) 1077 return -ENXIO; 1078 1079 /* read modem signals automatically whenever they change */ 1080 buf[0] = DIGI_CMD_READ_INPUT_SIGNALS; 1081 buf[1] = priv->dp_port_num; 1082 buf[2] = DIGI_ENABLE; 1083 buf[3] = 0; 1084 1085 /* flush fifos */ 1086 buf[4] = DIGI_CMD_IFLUSH_FIFO; 1087 buf[5] = priv->dp_port_num; 1088 buf[6] = DIGI_FLUSH_TX | DIGI_FLUSH_RX; 1089 buf[7] = 0; 1090 1091 ret = digi_write_oob_command(port, buf, 8, 1); 1092 if (ret != 0) 1093 dev_dbg(&port->dev, "digi_open: write oob failed, ret=%d\n", ret); 1094 1095 /* set termios settings */ 1096 if (tty) { 1097 not_termios.c_cflag = ~tty->termios.c_cflag; 1098 not_termios.c_iflag = ~tty->termios.c_iflag; 1099 digi_set_termios(tty, port, ¬_termios); 1100 } 1101 return 0; 1102} 1103 1104 1105static void digi_close(struct usb_serial_port *port) 1106{ 1107 DEFINE_WAIT(wait); 1108 int ret; 1109 unsigned char buf[32]; 1110 struct digi_port *priv = usb_get_serial_port_data(port); 1111 1112 mutex_lock(&port->serial->disc_mutex); 1113 /* if disconnected, just clear flags */ 1114 if (port->serial->disconnected) 1115 goto exit; 1116 1117 /* FIXME: Transmit idle belongs in the wait_unti_sent path */ 1118 digi_transmit_idle(port, DIGI_CLOSE_TIMEOUT); 1119 1120 /* disable input flow control */ 1121 buf[0] = DIGI_CMD_SET_INPUT_FLOW_CONTROL; 1122 buf[1] = priv->dp_port_num; 1123 buf[2] = DIGI_DISABLE; 1124 buf[3] = 0; 1125 1126 /* disable output flow control */ 1127 buf[4] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL; 1128 buf[5] = priv->dp_port_num; 1129 buf[6] = DIGI_DISABLE; 1130 buf[7] = 0; 1131 1132 /* disable reading modem signals automatically */ 1133 buf[8] = DIGI_CMD_READ_INPUT_SIGNALS; 1134 buf[9] = priv->dp_port_num; 1135 buf[10] = DIGI_DISABLE; 1136 buf[11] = 0; 1137 1138 /* disable receive */ 1139 buf[12] = DIGI_CMD_RECEIVE_ENABLE; 1140 buf[13] = priv->dp_port_num; 1141 buf[14] = DIGI_DISABLE; 1142 buf[15] = 0; 1143 1144 /* flush fifos */ 1145 buf[16] = DIGI_CMD_IFLUSH_FIFO; 1146 buf[17] = priv->dp_port_num; 1147 buf[18] = DIGI_FLUSH_TX | DIGI_FLUSH_RX; 1148 buf[19] = 0; 1149 1150 ret = digi_write_oob_command(port, buf, 20, 0); 1151 if (ret != 0) 1152 dev_dbg(&port->dev, "digi_close: write oob failed, ret=%d\n", 1153 ret); 1154 /* wait for final commands on oob port to complete */ 1155 prepare_to_wait(&priv->dp_flush_wait, &wait, 1156 TASK_INTERRUPTIBLE); 1157 schedule_timeout(DIGI_CLOSE_TIMEOUT); 1158 finish_wait(&priv->dp_flush_wait, &wait); 1159 1160 /* shutdown any outstanding bulk writes */ 1161 usb_kill_urb(port->write_urb); 1162exit: 1163 spin_lock_irq(&priv->dp_port_lock); 1164 priv->dp_write_urb_in_use = 0; 1165 wake_up_interruptible(&priv->dp_close_wait); 1166 spin_unlock_irq(&priv->dp_port_lock); 1167 mutex_unlock(&port->serial->disc_mutex); 1168} 1169 1170 1171/* 1172 * Digi Startup Device 1173 * 1174 * Starts reads on all ports. Must be called AFTER startup, with 1175 * urbs initialized. Returns 0 if successful, non-zero error otherwise. 1176 */ 1177 1178static int digi_startup_device(struct usb_serial *serial) 1179{ 1180 int i, ret = 0; 1181 struct digi_serial *serial_priv = usb_get_serial_data(serial); 1182 struct usb_serial_port *port; 1183 1184 /* be sure this happens exactly once */ 1185 spin_lock(&serial_priv->ds_serial_lock); 1186 if (serial_priv->ds_device_started) { 1187 spin_unlock(&serial_priv->ds_serial_lock); 1188 return 0; 1189 } 1190 serial_priv->ds_device_started = 1; 1191 spin_unlock(&serial_priv->ds_serial_lock); 1192 1193 /* start reading from each bulk in endpoint for the device */ 1194 /* set USB_DISABLE_SPD flag for write bulk urbs */ 1195 for (i = 0; i < serial->type->num_ports + 1; i++) { 1196 port = serial->port[i]; 1197 ret = usb_submit_urb(port->read_urb, GFP_KERNEL); 1198 if (ret != 0) { 1199 dev_err(&port->dev, 1200 "%s: usb_submit_urb failed, ret=%d, port=%d\n", 1201 __func__, ret, i); 1202 break; 1203 } 1204 } 1205 return ret; 1206} 1207 1208static int digi_port_init(struct usb_serial_port *port, unsigned port_num) 1209{ 1210 struct digi_port *priv; 1211 1212 priv = kzalloc(sizeof(*priv), GFP_KERNEL); 1213 if (!priv) 1214 return -ENOMEM; 1215 1216 spin_lock_init(&priv->dp_port_lock); 1217 priv->dp_port_num = port_num; 1218 init_waitqueue_head(&priv->dp_transmit_idle_wait); 1219 init_waitqueue_head(&priv->dp_flush_wait); 1220 init_waitqueue_head(&priv->dp_close_wait); 1221 init_waitqueue_head(&priv->write_wait); 1222 priv->dp_port = port; 1223 1224 usb_set_serial_port_data(port, priv); 1225 1226 return 0; 1227} 1228 1229static int digi_startup(struct usb_serial *serial) 1230{ 1231 struct digi_serial *serial_priv; 1232 int ret; 1233 1234 serial_priv = kzalloc(sizeof(*serial_priv), GFP_KERNEL); 1235 if (!serial_priv) 1236 return -ENOMEM; 1237 1238 spin_lock_init(&serial_priv->ds_serial_lock); 1239 serial_priv->ds_oob_port_num = serial->type->num_ports; 1240 serial_priv->ds_oob_port = serial->port[serial_priv->ds_oob_port_num]; 1241 1242 ret = digi_port_init(serial_priv->ds_oob_port, 1243 serial_priv->ds_oob_port_num); 1244 if (ret) { 1245 kfree(serial_priv); 1246 return ret; 1247 } 1248 1249 usb_set_serial_data(serial, serial_priv); 1250 1251 return 0; 1252} 1253 1254 1255static void digi_disconnect(struct usb_serial *serial) 1256{ 1257 int i; 1258 1259 /* stop reads and writes on all ports */ 1260 for (i = 0; i < serial->type->num_ports + 1; i++) { 1261 usb_kill_urb(serial->port[i]->read_urb); 1262 usb_kill_urb(serial->port[i]->write_urb); 1263 } 1264} 1265 1266 1267static void digi_release(struct usb_serial *serial) 1268{ 1269 struct digi_serial *serial_priv; 1270 struct digi_port *priv; 1271 1272 serial_priv = usb_get_serial_data(serial); 1273 1274 priv = usb_get_serial_port_data(serial_priv->ds_oob_port); 1275 kfree(priv); 1276 1277 kfree(serial_priv); 1278} 1279 1280static int digi_port_probe(struct usb_serial_port *port) 1281{ 1282 return digi_port_init(port, port->port_number); 1283} 1284 1285static void digi_port_remove(struct usb_serial_port *port) 1286{ 1287 struct digi_port *priv; 1288 1289 priv = usb_get_serial_port_data(port); 1290 kfree(priv); 1291} 1292 1293static void digi_read_bulk_callback(struct urb *urb) 1294{ 1295 struct usb_serial_port *port = urb->context; 1296 struct digi_port *priv; 1297 struct digi_serial *serial_priv; 1298 int ret; 1299 int status = urb->status; 1300 1301 /* port sanity check, do not resubmit if port is not valid */ 1302 if (port == NULL) 1303 return; 1304 priv = usb_get_serial_port_data(port); 1305 if (priv == NULL) { 1306 dev_err(&port->dev, "%s: port->private is NULL, status=%d\n", 1307 __func__, status); 1308 return; 1309 } 1310 if (port->serial == NULL || 1311 (serial_priv = usb_get_serial_data(port->serial)) == NULL) { 1312 dev_err(&port->dev, "%s: serial is bad or serial->private " 1313 "is NULL, status=%d\n", __func__, status); 1314 return; 1315 } 1316 1317 /* do not resubmit urb if it has any status error */ 1318 if (status) { 1319 dev_err(&port->dev, 1320 "%s: nonzero read bulk status: status=%d, port=%d\n", 1321 __func__, status, priv->dp_port_num); 1322 return; 1323 } 1324 1325 /* handle oob or inb callback, do not resubmit if error */ 1326 if (priv->dp_port_num == serial_priv->ds_oob_port_num) { 1327 if (digi_read_oob_callback(urb) != 0) 1328 return; 1329 } else { 1330 if (digi_read_inb_callback(urb) != 0) 1331 return; 1332 } 1333 1334 /* continue read */ 1335 ret = usb_submit_urb(urb, GFP_ATOMIC); 1336 if (ret != 0 && ret != -EPERM) { 1337 dev_err(&port->dev, 1338 "%s: failed resubmitting urb, ret=%d, port=%d\n", 1339 __func__, ret, priv->dp_port_num); 1340 } 1341 1342} 1343 1344/* 1345 * Digi Read INB Callback 1346 * 1347 * Digi Read INB Callback handles reads on the in band ports, sending 1348 * the data on to the tty subsystem. When called we know port and 1349 * port->private are not NULL and port->serial has been validated. 1350 * It returns 0 if successful, 1 if successful but the port is 1351 * throttled, and -1 if the sanity checks failed. 1352 */ 1353 1354static int digi_read_inb_callback(struct urb *urb) 1355{ 1356 struct usb_serial_port *port = urb->context; 1357 struct digi_port *priv = usb_get_serial_port_data(port); 1358 unsigned char *buf = urb->transfer_buffer; 1359 unsigned long flags; 1360 int opcode; 1361 int len; 1362 int port_status; 1363 unsigned char *data; 1364 int tty_flag, throttled; 1365 1366 /* short/multiple packet check */ 1367 if (urb->actual_length < 2) { 1368 dev_warn(&port->dev, "short packet received\n"); 1369 return -1; 1370 } 1371 1372 opcode = buf[0]; 1373 len = buf[1]; 1374 1375 if (urb->actual_length != len + 2) { 1376 dev_err(&port->dev, "malformed packet received: port=%d, opcode=%d, len=%d, actual_length=%u\n", 1377 priv->dp_port_num, opcode, len, urb->actual_length); 1378 return -1; 1379 } 1380 1381 if (opcode == DIGI_CMD_RECEIVE_DATA && len < 1) { 1382 dev_err(&port->dev, "malformed data packet received\n"); 1383 return -1; 1384 } 1385 1386 spin_lock_irqsave(&priv->dp_port_lock, flags); 1387 1388 /* check for throttle; if set, do not resubmit read urb */ 1389 /* indicate the read chain needs to be restarted on unthrottle */ 1390 throttled = priv->dp_throttled; 1391 if (throttled) 1392 priv->dp_throttle_restart = 1; 1393 1394 /* receive data */ 1395 if (opcode == DIGI_CMD_RECEIVE_DATA) { 1396 port_status = buf[2]; 1397 data = &buf[3]; 1398 1399 /* get flag from port_status */ 1400 tty_flag = 0; 1401 1402 /* overrun is special, not associated with a char */ 1403 if (port_status & DIGI_OVERRUN_ERROR) 1404 tty_insert_flip_char(&port->port, 0, TTY_OVERRUN); 1405 1406 /* break takes precedence over parity, */ 1407 /* which takes precedence over framing errors */ 1408 if (port_status & DIGI_BREAK_ERROR) 1409 tty_flag = TTY_BREAK; 1410 else if (port_status & DIGI_PARITY_ERROR) 1411 tty_flag = TTY_PARITY; 1412 else if (port_status & DIGI_FRAMING_ERROR) 1413 tty_flag = TTY_FRAME; 1414 1415 /* data length is len-1 (one byte of len is port_status) */ 1416 --len; 1417 if (len > 0) { 1418 tty_insert_flip_string_fixed_flag(&port->port, data, 1419 tty_flag, len); 1420 tty_flip_buffer_push(&port->port); 1421 } 1422 } 1423 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 1424 1425 if (opcode == DIGI_CMD_RECEIVE_DISABLE) 1426 dev_dbg(&port->dev, "%s: got RECEIVE_DISABLE\n", __func__); 1427 else if (opcode != DIGI_CMD_RECEIVE_DATA) 1428 dev_dbg(&port->dev, "%s: unknown opcode: %d\n", __func__, opcode); 1429 1430 return throttled ? 1 : 0; 1431 1432} 1433 1434 1435/* 1436 * Digi Read OOB Callback 1437 * 1438 * Digi Read OOB Callback handles reads on the out of band port. 1439 * When called we know port and port->private are not NULL and 1440 * the port->serial is valid. It returns 0 if successful, and 1441 * -1 if the sanity checks failed. 1442 */ 1443 1444static int digi_read_oob_callback(struct urb *urb) 1445{ 1446 1447 struct usb_serial_port *port = urb->context; 1448 struct usb_serial *serial = port->serial; 1449 struct tty_struct *tty; 1450 struct digi_port *priv; 1451 unsigned char *buf = urb->transfer_buffer; 1452 int opcode, line, status, val; 1453 unsigned long flags; 1454 int i; 1455 unsigned int rts; 1456 1457 if (urb->actual_length < 4) 1458 return -1; 1459 1460 /* handle each oob command */ 1461 for (i = 0; i < urb->actual_length - 3; i += 4) { 1462 opcode = buf[i]; 1463 line = buf[i + 1]; 1464 status = buf[i + 2]; 1465 val = buf[i + 3]; 1466 1467 dev_dbg(&port->dev, "digi_read_oob_callback: opcode=%d, line=%d, status=%d, val=%d\n", 1468 opcode, line, status, val); 1469 1470 if (status != 0 || line >= serial->type->num_ports) 1471 continue; 1472 1473 port = serial->port[line]; 1474 1475 priv = usb_get_serial_port_data(port); 1476 if (priv == NULL) 1477 return -1; 1478 1479 tty = tty_port_tty_get(&port->port); 1480 1481 rts = 0; 1482 if (tty) 1483 rts = C_CRTSCTS(tty); 1484 1485 if (tty && opcode == DIGI_CMD_READ_INPUT_SIGNALS) { 1486 bool wakeup = false; 1487 1488 spin_lock_irqsave(&priv->dp_port_lock, flags); 1489 /* convert from digi flags to termiox flags */ 1490 if (val & DIGI_READ_INPUT_SIGNALS_CTS) { 1491 priv->dp_modem_signals |= TIOCM_CTS; 1492 if (rts) 1493 wakeup = true; 1494 } else { 1495 priv->dp_modem_signals &= ~TIOCM_CTS; 1496 /* port must be open to use tty struct */ 1497 } 1498 if (val & DIGI_READ_INPUT_SIGNALS_DSR) 1499 priv->dp_modem_signals |= TIOCM_DSR; 1500 else 1501 priv->dp_modem_signals &= ~TIOCM_DSR; 1502 if (val & DIGI_READ_INPUT_SIGNALS_RI) 1503 priv->dp_modem_signals |= TIOCM_RI; 1504 else 1505 priv->dp_modem_signals &= ~TIOCM_RI; 1506 if (val & DIGI_READ_INPUT_SIGNALS_DCD) 1507 priv->dp_modem_signals |= TIOCM_CD; 1508 else 1509 priv->dp_modem_signals &= ~TIOCM_CD; 1510 1511 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 1512 1513 if (wakeup) 1514 tty_port_tty_wakeup(&port->port); 1515 } else if (opcode == DIGI_CMD_TRANSMIT_IDLE) { 1516 spin_lock_irqsave(&priv->dp_port_lock, flags); 1517 priv->dp_transmit_idle = 1; 1518 wake_up_interruptible(&priv->dp_transmit_idle_wait); 1519 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 1520 } else if (opcode == DIGI_CMD_IFLUSH_FIFO) { 1521 wake_up_interruptible(&priv->dp_flush_wait); 1522 } 1523 tty_kref_put(tty); 1524 } 1525 return 0; 1526 1527} 1528 1529module_usb_serial_driver(serial_drivers, id_table_combined); 1530 1531MODULE_AUTHOR(DRIVER_AUTHOR); 1532MODULE_DESCRIPTION(DRIVER_DESC); 1533MODULE_LICENSE("GPL");
~/
Read-only file preview.