FILE
NCR5380.c
File preview with syntax highlighting.
linux-6.19.14/drivers/scsi/NCR5380.c
1// SPDX-License-Identifier: GPL-2.0 2/* 3 * NCR 5380 generic driver routines. These should make it *trivial* 4 * to implement 5380 SCSI drivers under Linux with a non-trantor 5 * architecture. 6 * 7 * Note that these routines also work with NR53c400 family chips. 8 * 9 * Copyright 1993, Drew Eckhardt 10 * Visionary Computing 11 * (Unix and Linux consulting and custom programming) 12 * drew@colorado.edu 13 * +1 (303) 666-5836 14 * 15 * For more information, please consult 16 * 17 * NCR 5380 Family 18 * SCSI Protocol Controller 19 * Databook 20 * 21 * NCR Microelectronics 22 * 1635 Aeroplaza Drive 23 * Colorado Springs, CO 80916 24 * 1+ (719) 578-3400 25 * 1+ (800) 334-5454 26 */ 27 28/* 29 * With contributions from Ray Van Tassle, Ingmar Baumgart, 30 * Ronald van Cuijlenborg, Alan Cox and others. 31 */ 32 33/* Ported to Atari by Roman Hodek and others. */ 34 35/* Adapted for the Sun 3 by Sam Creasey. */ 36 37/* 38 * Design 39 * 40 * This is a generic 5380 driver. To use it on a different platform, 41 * one simply writes appropriate system specific macros (ie, data 42 * transfer - some PC's will use the I/O bus, 68K's must use 43 * memory mapped) and drops this file in their 'C' wrapper. 44 * 45 * As far as command queueing, two queues are maintained for 46 * each 5380 in the system - commands that haven't been issued yet, 47 * and commands that are currently executing. This means that an 48 * unlimited number of commands may be queued, letting 49 * more commands propagate from the higher driver levels giving higher 50 * throughput. Note that both I_T_L and I_T_L_Q nexuses are supported, 51 * allowing multiple commands to propagate all the way to a SCSI-II device 52 * while a command is already executing. 53 * 54 * 55 * Issues specific to the NCR5380 : 56 * 57 * When used in a PIO or pseudo-dma mode, the NCR5380 is a braindead 58 * piece of hardware that requires you to sit in a loop polling for 59 * the REQ signal as long as you are connected. Some devices are 60 * brain dead (ie, many TEXEL CD ROM drives) and won't disconnect 61 * while doing long seek operations. [...] These 62 * broken devices are the exception rather than the rule and I'd rather 63 * spend my time optimizing for the normal case. 64 * 65 * Architecture : 66 * 67 * At the heart of the design is a coroutine, NCR5380_main, 68 * which is started from a workqueue for each NCR5380 host in the 69 * system. It attempts to establish I_T_L or I_T_L_Q nexuses by 70 * removing the commands from the issue queue and calling 71 * NCR5380_select() if a nexus is not established. 72 * 73 * Once a nexus is established, the NCR5380_information_transfer() 74 * phase goes through the various phases as instructed by the target. 75 * if the target goes into MSG IN and sends a DISCONNECT message, 76 * the command structure is placed into the per instance disconnected 77 * queue, and NCR5380_main tries to find more work. If the target is 78 * idle for too long, the system will try to sleep. 79 * 80 * If a command has disconnected, eventually an interrupt will trigger, 81 * calling NCR5380_intr() which will in turn call NCR5380_reselect 82 * to reestablish a nexus. This will run main if necessary. 83 * 84 * On command termination, the done function will be called as 85 * appropriate. 86 * 87 * The command data pointer is initialized after the command is connected 88 * in NCR5380_select, and set as appropriate in NCR5380_information_transfer. 89 * Note that in violation of the standard, an implicit SAVE POINTERS operation 90 * is done, since some BROKEN disks fail to issue an explicit SAVE POINTERS. 91 */ 92 93/* 94 * Using this file : 95 * This file a skeleton Linux SCSI driver for the NCR 5380 series 96 * of chips. To use it, you write an architecture specific functions 97 * and macros and include this file in your driver. 98 * 99 * These macros MUST be defined : 100 * 101 * NCR5380_read(register) - read from the specified register 102 * 103 * NCR5380_write(register, value) - write to the specific register 104 * 105 * NCR5380_implementation_fields - additional fields needed for this 106 * specific implementation of the NCR5380 107 * 108 * Either real DMA *or* pseudo DMA may be implemented 109 * 110 * NCR5380_dma_xfer_len - determine size of DMA/PDMA transfer 111 * NCR5380_dma_send_setup - execute DMA/PDMA from memory to 5380 112 * NCR5380_dma_recv_setup - execute DMA/PDMA from 5380 to memory 113 * NCR5380_dma_residual - residual byte count 114 * 115 * The generic driver is initialized by calling NCR5380_init(instance), 116 * after setting the appropriate host specific fields and ID. 117 */ 118 119#ifndef NCR5380_io_delay 120#define NCR5380_io_delay(x) 121#endif 122 123#ifndef NCR5380_acquire_dma_irq 124#define NCR5380_acquire_dma_irq(x) (1) 125#endif 126 127#ifndef NCR5380_release_dma_irq 128#define NCR5380_release_dma_irq(x) 129#endif 130 131static unsigned int disconnect_mask = ~0; 132module_param(disconnect_mask, int, 0444); 133 134static int do_abort(struct Scsi_Host *, unsigned int); 135static void do_reset(struct Scsi_Host *); 136static void bus_reset_cleanup(struct Scsi_Host *); 137 138/** 139 * initialize_SCp - init the scsi pointer field 140 * @cmd: command block to set up 141 * 142 * Set up the internal fields in the SCSI command. 143 */ 144 145static inline void initialize_SCp(struct scsi_cmnd *cmd) 146{ 147 struct NCR5380_cmd *ncmd = NCR5380_to_ncmd(cmd); 148 149 if (scsi_bufflen(cmd)) { 150 ncmd->buffer = scsi_sglist(cmd); 151 ncmd->ptr = sg_virt(ncmd->buffer); 152 ncmd->this_residual = ncmd->buffer->length; 153 } else { 154 ncmd->buffer = NULL; 155 ncmd->ptr = NULL; 156 ncmd->this_residual = 0; 157 } 158 159 ncmd->status = 0; 160} 161 162static inline void advance_sg_buffer(struct NCR5380_cmd *ncmd) 163{ 164 struct scatterlist *s = ncmd->buffer; 165 166 if (!ncmd->this_residual && s && !sg_is_last(s)) { 167 ncmd->buffer = sg_next(s); 168 ncmd->ptr = sg_virt(ncmd->buffer); 169 ncmd->this_residual = ncmd->buffer->length; 170 } 171} 172 173static inline void set_resid_from_SCp(struct scsi_cmnd *cmd) 174{ 175 struct NCR5380_cmd *ncmd = NCR5380_to_ncmd(cmd); 176 int resid = ncmd->this_residual; 177 struct scatterlist *s = ncmd->buffer; 178 179 if (s) 180 while (!sg_is_last(s)) { 181 s = sg_next(s); 182 resid += s->length; 183 } 184 scsi_set_resid(cmd, resid); 185} 186 187/** 188 * NCR5380_poll_politely2 - wait for two chip register values 189 * @hostdata: host private data 190 * @reg1: 5380 register to poll 191 * @bit1: Bitmask to check 192 * @val1: Expected value 193 * @reg2: Second 5380 register to poll 194 * @bit2: Second bitmask to check 195 * @val2: Second expected value 196 * @wait: Time-out in jiffies, 0 if sleeping is not allowed 197 * 198 * Polls the chip in a reasonably efficient manner waiting for an 199 * event to occur. After a short quick poll we begin to yield the CPU 200 * (if possible). In irq contexts the time-out is arbitrarily limited. 201 * 202 * Returns 0 if either or both event(s) occurred otherwise -ETIMEDOUT. 203 */ 204 205static int NCR5380_poll_politely2(struct NCR5380_hostdata *hostdata, 206 unsigned int reg1, u8 bit1, u8 val1, 207 unsigned int reg2, u8 bit2, u8 val2, 208 unsigned long wait) 209{ 210 unsigned long n = hostdata->poll_loops; 211 unsigned long deadline = jiffies + wait; 212 213 do { 214 if ((NCR5380_read(reg1) & bit1) == val1) 215 return 0; 216 if ((NCR5380_read(reg2) & bit2) == val2) 217 return 0; 218 cpu_relax(); 219 } while (n--); 220 221 if (!wait) 222 return -ETIMEDOUT; 223 224 /* Repeatedly sleep for 1 ms until deadline */ 225 while (time_is_after_jiffies(deadline)) { 226 schedule_timeout_uninterruptible(1); 227 if ((NCR5380_read(reg1) & bit1) == val1) 228 return 0; 229 if ((NCR5380_read(reg2) & bit2) == val2) 230 return 0; 231 } 232 233 return -ETIMEDOUT; 234} 235 236#if NDEBUG 237static struct { 238 unsigned char mask; 239 const char *name; 240} signals[] = { 241 {SR_DBP, "PARITY"}, 242 {SR_RST, "RST"}, 243 {SR_BSY, "BSY"}, 244 {SR_REQ, "REQ"}, 245 {SR_MSG, "MSG"}, 246 {SR_CD, "CD"}, 247 {SR_IO, "IO"}, 248 {SR_SEL, "SEL"}, 249 {0, NULL} 250}, 251basrs[] = { 252 {BASR_END_DMA_TRANSFER, "END OF DMA"}, 253 {BASR_DRQ, "DRQ"}, 254 {BASR_PARITY_ERROR, "PARITY ERROR"}, 255 {BASR_IRQ, "IRQ"}, 256 {BASR_PHASE_MATCH, "PHASE MATCH"}, 257 {BASR_BUSY_ERROR, "BUSY ERROR"}, 258 {BASR_ATN, "ATN"}, 259 {BASR_ACK, "ACK"}, 260 {0, NULL} 261}, 262icrs[] = { 263 {ICR_ASSERT_RST, "ASSERT RST"}, 264 {ICR_ARBITRATION_PROGRESS, "ARB. IN PROGRESS"}, 265 {ICR_ARBITRATION_LOST, "LOST ARB."}, 266 {ICR_ASSERT_ACK, "ASSERT ACK"}, 267 {ICR_ASSERT_BSY, "ASSERT BSY"}, 268 {ICR_ASSERT_SEL, "ASSERT SEL"}, 269 {ICR_ASSERT_ATN, "ASSERT ATN"}, 270 {ICR_ASSERT_DATA, "ASSERT DATA"}, 271 {0, NULL} 272}, 273mrs[] = { 274 {MR_BLOCK_DMA_MODE, "BLOCK DMA MODE"}, 275 {MR_TARGET, "TARGET"}, 276 {MR_ENABLE_PAR_CHECK, "PARITY CHECK"}, 277 {MR_ENABLE_PAR_INTR, "PARITY INTR"}, 278 {MR_ENABLE_EOP_INTR, "EOP INTR"}, 279 {MR_MONITOR_BSY, "MONITOR BSY"}, 280 {MR_DMA_MODE, "DMA MODE"}, 281 {MR_ARBITRATE, "ARBITRATE"}, 282 {0, NULL} 283}; 284 285/** 286 * NCR5380_print - print scsi bus signals 287 * @instance: adapter state to dump 288 * 289 * Print the SCSI bus signals for debugging purposes 290 */ 291 292static void NCR5380_print(struct Scsi_Host *instance) 293{ 294 struct NCR5380_hostdata *hostdata = shost_priv(instance); 295 unsigned char status, basr, mr, icr, i; 296 297 status = NCR5380_read(STATUS_REG); 298 mr = NCR5380_read(MODE_REG); 299 icr = NCR5380_read(INITIATOR_COMMAND_REG); 300 basr = NCR5380_read(BUS_AND_STATUS_REG); 301 302 printk(KERN_DEBUG "SR = 0x%02x : ", status); 303 for (i = 0; signals[i].mask; ++i) 304 if (status & signals[i].mask) 305 printk(KERN_CONT "%s, ", signals[i].name); 306 printk(KERN_CONT "\nBASR = 0x%02x : ", basr); 307 for (i = 0; basrs[i].mask; ++i) 308 if (basr & basrs[i].mask) 309 printk(KERN_CONT "%s, ", basrs[i].name); 310 printk(KERN_CONT "\nICR = 0x%02x : ", icr); 311 for (i = 0; icrs[i].mask; ++i) 312 if (icr & icrs[i].mask) 313 printk(KERN_CONT "%s, ", icrs[i].name); 314 printk(KERN_CONT "\nMR = 0x%02x : ", mr); 315 for (i = 0; mrs[i].mask; ++i) 316 if (mr & mrs[i].mask) 317 printk(KERN_CONT "%s, ", mrs[i].name); 318 printk(KERN_CONT "\n"); 319} 320 321static struct { 322 unsigned char value; 323 const char *name; 324} phases[] = { 325 {PHASE_DATAOUT, "DATAOUT"}, 326 {PHASE_DATAIN, "DATAIN"}, 327 {PHASE_CMDOUT, "CMDOUT"}, 328 {PHASE_STATIN, "STATIN"}, 329 {PHASE_MSGOUT, "MSGOUT"}, 330 {PHASE_MSGIN, "MSGIN"}, 331 {PHASE_UNKNOWN, "UNKNOWN"} 332}; 333 334/** 335 * NCR5380_print_phase - show SCSI phase 336 * @instance: adapter to dump 337 * 338 * Print the current SCSI phase for debugging purposes 339 */ 340 341static void NCR5380_print_phase(struct Scsi_Host *instance) 342{ 343 struct NCR5380_hostdata *hostdata = shost_priv(instance); 344 unsigned char status; 345 int i; 346 347 status = NCR5380_read(STATUS_REG); 348 if (!(status & SR_REQ)) 349 shost_printk(KERN_DEBUG, instance, "REQ not asserted, phase unknown.\n"); 350 else { 351 for (i = 0; (phases[i].value != PHASE_UNKNOWN) && 352 (phases[i].value != (status & PHASE_MASK)); ++i) 353 ; 354 shost_printk(KERN_DEBUG, instance, "phase %s\n", phases[i].name); 355 } 356} 357#endif 358 359/** 360 * NCR5380_info - report driver and host information 361 * @instance: relevant scsi host instance 362 * 363 * For use as the host template info() handler. 364 */ 365 366static const char *NCR5380_info(struct Scsi_Host *instance) 367{ 368 struct NCR5380_hostdata *hostdata = shost_priv(instance); 369 370 return hostdata->info; 371} 372 373/** 374 * NCR5380_init - initialise an NCR5380 375 * @instance: adapter to configure 376 * @flags: control flags 377 * 378 * Initializes *instance and corresponding 5380 chip, 379 * with flags OR'd into the initial flags value. 380 * 381 * Notes : I assume that the host, hostno, and id bits have been 382 * set correctly. I don't care about the irq and other fields. 383 * 384 * Returns 0 for success 385 */ 386 387static int NCR5380_init(struct Scsi_Host *instance, int flags) 388{ 389 struct NCR5380_hostdata *hostdata = shost_priv(instance); 390 int i; 391 unsigned long deadline; 392 unsigned long accesses_per_ms; 393 394 instance->max_lun = 7; 395 396 hostdata->host = instance; 397 hostdata->id_mask = 1 << instance->this_id; 398 hostdata->id_higher_mask = 0; 399 for (i = hostdata->id_mask; i <= 0x80; i <<= 1) 400 if (i > hostdata->id_mask) 401 hostdata->id_higher_mask |= i; 402 for (i = 0; i < 8; ++i) 403 hostdata->busy[i] = 0; 404 hostdata->dma_len = 0; 405 406 spin_lock_init(&hostdata->lock); 407 hostdata->connected = NULL; 408 hostdata->sensing = NULL; 409 INIT_LIST_HEAD(&hostdata->autosense); 410 INIT_LIST_HEAD(&hostdata->unissued); 411 INIT_LIST_HEAD(&hostdata->disconnected); 412 413 hostdata->flags = flags; 414 415 INIT_WORK(&hostdata->main_task, NCR5380_main); 416 hostdata->work_q = alloc_workqueue("ncr5380_%d", 417 WQ_UNBOUND | WQ_MEM_RECLAIM, 418 0, instance->host_no); 419 if (!hostdata->work_q) 420 return -ENOMEM; 421 422 snprintf(hostdata->info, sizeof(hostdata->info), 423 "%s, irq %d, io_port 0x%lx, base 0x%lx, can_queue %d, cmd_per_lun %d, sg_tablesize %d, this_id %d, flags { %s%s%s}", 424 instance->hostt->name, instance->irq, hostdata->io_port, 425 hostdata->base, instance->can_queue, instance->cmd_per_lun, 426 instance->sg_tablesize, instance->this_id, 427 hostdata->flags & FLAG_DMA_FIXUP ? "DMA_FIXUP " : "", 428 hostdata->flags & FLAG_NO_PSEUDO_DMA ? "NO_PSEUDO_DMA " : "", 429 hostdata->flags & FLAG_TOSHIBA_DELAY ? "TOSHIBA_DELAY " : ""); 430 431 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 432 NCR5380_write(MODE_REG, MR_BASE); 433 NCR5380_write(TARGET_COMMAND_REG, 0); 434 NCR5380_write(SELECT_ENABLE_REG, 0); 435 436 /* Calibrate register polling loop */ 437 i = 0; 438 deadline = jiffies + 1; 439 do { 440 cpu_relax(); 441 } while (time_is_after_jiffies(deadline)); 442 deadline += msecs_to_jiffies(256); 443 do { 444 NCR5380_read(STATUS_REG); 445 ++i; 446 cpu_relax(); 447 } while (time_is_after_jiffies(deadline)); 448 accesses_per_ms = i / 256; 449 hostdata->poll_loops = NCR5380_REG_POLL_TIME * accesses_per_ms / 2; 450 451 return 0; 452} 453 454/** 455 * NCR5380_maybe_reset_bus - Detect and correct bus wedge problems. 456 * @instance: adapter to check 457 * 458 * If the system crashed, it may have crashed with a connected target and 459 * the SCSI bus busy. Check for BUS FREE phase. If not, try to abort the 460 * currently established nexus, which we know nothing about. Failing that 461 * do a bus reset. 462 * 463 * Note that a bus reset will cause the chip to assert IRQ. 464 * 465 * Returns 0 if successful, otherwise -ENXIO. 466 */ 467 468static int NCR5380_maybe_reset_bus(struct Scsi_Host *instance) 469{ 470 struct NCR5380_hostdata *hostdata = shost_priv(instance); 471 int pass; 472 473 for (pass = 1; (NCR5380_read(STATUS_REG) & SR_BSY) && pass <= 6; ++pass) { 474 switch (pass) { 475 case 1: 476 case 3: 477 case 5: 478 shost_printk(KERN_ERR, instance, "SCSI bus busy, waiting up to five seconds\n"); 479 NCR5380_poll_politely(hostdata, 480 STATUS_REG, SR_BSY, 0, 5 * HZ); 481 break; 482 case 2: 483 shost_printk(KERN_ERR, instance, "bus busy, attempting abort\n"); 484 do_abort(instance, 1); 485 break; 486 case 4: 487 shost_printk(KERN_ERR, instance, "bus busy, attempting reset\n"); 488 do_reset(instance); 489 /* Wait after a reset; the SCSI standard calls for 490 * 250ms, we wait 500ms to be on the safe side. 491 * But some Toshiba CD-ROMs need ten times that. 492 */ 493 if (hostdata->flags & FLAG_TOSHIBA_DELAY) 494 msleep(2500); 495 else 496 msleep(500); 497 break; 498 case 6: 499 shost_printk(KERN_ERR, instance, "bus locked solid\n"); 500 return -ENXIO; 501 } 502 } 503 return 0; 504} 505 506/** 507 * NCR5380_exit - remove an NCR5380 508 * @instance: adapter to remove 509 * 510 * Assumes that no more work can be queued (e.g. by NCR5380_intr). 511 */ 512 513static void NCR5380_exit(struct Scsi_Host *instance) 514{ 515 struct NCR5380_hostdata *hostdata = shost_priv(instance); 516 517 cancel_work_sync(&hostdata->main_task); 518 destroy_workqueue(hostdata->work_q); 519} 520 521/** 522 * complete_cmd - finish processing a command and return it to the SCSI ML 523 * @instance: the host instance 524 * @cmd: command to complete 525 */ 526 527static void complete_cmd(struct Scsi_Host *instance, 528 struct scsi_cmnd *cmd) 529{ 530 struct NCR5380_hostdata *hostdata = shost_priv(instance); 531 532 dsprintk(NDEBUG_QUEUES, instance, "complete_cmd: cmd %p\n", cmd); 533 534 if (hostdata->sensing == cmd) { 535 /* Autosense processing ends here */ 536 if (get_status_byte(cmd) != SAM_STAT_GOOD) { 537 scsi_eh_restore_cmnd(cmd, &hostdata->ses); 538 } else { 539 scsi_eh_restore_cmnd(cmd, &hostdata->ses); 540 set_status_byte(cmd, SAM_STAT_CHECK_CONDITION); 541 } 542 hostdata->sensing = NULL; 543 } 544 545 scsi_done(cmd); 546} 547 548/** 549 * NCR5380_queue_command - queue a command 550 * @instance: the relevant SCSI adapter 551 * @cmd: SCSI command 552 * 553 * cmd is added to the per-instance issue queue, with minor 554 * twiddling done to the host specific fields of cmd. If the 555 * main coroutine is not running, it is restarted. 556 */ 557 558static int NCR5380_queue_command(struct Scsi_Host *instance, 559 struct scsi_cmnd *cmd) 560{ 561 struct NCR5380_hostdata *hostdata = shost_priv(instance); 562 struct NCR5380_cmd *ncmd = NCR5380_to_ncmd(cmd); 563 unsigned long flags; 564 565#if (NDEBUG & NDEBUG_NO_WRITE) 566 switch (cmd->cmnd[0]) { 567 case WRITE_6: 568 case WRITE_10: 569 shost_printk(KERN_DEBUG, instance, "WRITE attempted with NDEBUG_NO_WRITE set\n"); 570 cmd->result = (DID_ERROR << 16); 571 scsi_done(cmd); 572 return 0; 573 } 574#endif /* (NDEBUG & NDEBUG_NO_WRITE) */ 575 576 cmd->result = 0; 577 578 spin_lock_irqsave(&hostdata->lock, flags); 579 580 if (!NCR5380_acquire_dma_irq(instance)) { 581 spin_unlock_irqrestore(&hostdata->lock, flags); 582 583 return SCSI_MLQUEUE_HOST_BUSY; 584 } 585 586 /* 587 * Insert the cmd into the issue queue. Note that REQUEST SENSE 588 * commands are added to the head of the queue since any command will 589 * clear the contingent allegiance condition that exists and the 590 * sense data is only guaranteed to be valid while the condition exists. 591 */ 592 593 if (cmd->cmnd[0] == REQUEST_SENSE) 594 list_add(&ncmd->list, &hostdata->unissued); 595 else 596 list_add_tail(&ncmd->list, &hostdata->unissued); 597 598 spin_unlock_irqrestore(&hostdata->lock, flags); 599 600 dsprintk(NDEBUG_QUEUES, instance, "command %p added to %s of queue\n", 601 cmd, (cmd->cmnd[0] == REQUEST_SENSE) ? "head" : "tail"); 602 603 /* Kick off command processing */ 604 queue_work(hostdata->work_q, &hostdata->main_task); 605 return 0; 606} 607 608static inline void maybe_release_dma_irq(struct Scsi_Host *instance) 609{ 610 struct NCR5380_hostdata *hostdata = shost_priv(instance); 611 612 /* Caller does the locking needed to set & test these data atomically */ 613 if (list_empty(&hostdata->disconnected) && 614 list_empty(&hostdata->unissued) && 615 list_empty(&hostdata->autosense) && 616 !hostdata->connected && 617 !hostdata->selecting) { 618 NCR5380_release_dma_irq(instance); 619 } 620} 621 622/** 623 * dequeue_next_cmd - dequeue a command for processing 624 * @instance: the scsi host instance 625 * 626 * Priority is given to commands on the autosense queue. These commands 627 * need autosense because of a CHECK CONDITION result. 628 * 629 * Returns a command pointer if a command is found for a target that is 630 * not already busy. Otherwise returns NULL. 631 */ 632 633static struct scsi_cmnd *dequeue_next_cmd(struct Scsi_Host *instance) 634{ 635 struct NCR5380_hostdata *hostdata = shost_priv(instance); 636 struct NCR5380_cmd *ncmd; 637 struct scsi_cmnd *cmd; 638 639 if (hostdata->sensing || list_empty(&hostdata->autosense)) { 640 list_for_each_entry(ncmd, &hostdata->unissued, list) { 641 cmd = NCR5380_to_scmd(ncmd); 642 dsprintk(NDEBUG_QUEUES, instance, "dequeue: cmd=%p target=%d busy=0x%02x lun=%llu\n", 643 cmd, scmd_id(cmd), hostdata->busy[scmd_id(cmd)], cmd->device->lun); 644 645 if (!(hostdata->busy[scmd_id(cmd)] & (1 << cmd->device->lun))) { 646 list_del(&ncmd->list); 647 dsprintk(NDEBUG_QUEUES, instance, 648 "dequeue: removed %p from issue queue\n", cmd); 649 return cmd; 650 } 651 } 652 } else { 653 /* Autosense processing begins here */ 654 ncmd = list_first_entry(&hostdata->autosense, 655 struct NCR5380_cmd, list); 656 list_del(&ncmd->list); 657 cmd = NCR5380_to_scmd(ncmd); 658 dsprintk(NDEBUG_QUEUES, instance, 659 "dequeue: removed %p from autosense queue\n", cmd); 660 scsi_eh_prep_cmnd(cmd, &hostdata->ses, NULL, 0, ~0); 661 hostdata->sensing = cmd; 662 return cmd; 663 } 664 return NULL; 665} 666 667static void requeue_cmd(struct Scsi_Host *instance, struct scsi_cmnd *cmd) 668{ 669 struct NCR5380_hostdata *hostdata = shost_priv(instance); 670 struct NCR5380_cmd *ncmd = NCR5380_to_ncmd(cmd); 671 672 if (hostdata->sensing == cmd) { 673 scsi_eh_restore_cmnd(cmd, &hostdata->ses); 674 list_add(&ncmd->list, &hostdata->autosense); 675 hostdata->sensing = NULL; 676 } else 677 list_add(&ncmd->list, &hostdata->unissued); 678} 679 680/** 681 * NCR5380_main - NCR state machines 682 * 683 * NCR5380_main is a coroutine that runs as long as more work can 684 * be done on the NCR5380 host adapters in a system. Both 685 * NCR5380_queue_command() and NCR5380_intr() will try to start it 686 * in case it is not running. 687 */ 688 689static void NCR5380_main(struct work_struct *work) 690{ 691 struct NCR5380_hostdata *hostdata = 692 container_of(work, struct NCR5380_hostdata, main_task); 693 struct Scsi_Host *instance = hostdata->host; 694 int done; 695 696 do { 697 done = 1; 698 699 spin_lock_irq(&hostdata->lock); 700 while (!hostdata->connected && !hostdata->selecting) { 701 struct scsi_cmnd *cmd = dequeue_next_cmd(instance); 702 703 if (!cmd) 704 break; 705 706 dsprintk(NDEBUG_MAIN, instance, "main: dequeued %p\n", cmd); 707 708 /* 709 * Attempt to establish an I_T_L nexus here. 710 * On success, instance->hostdata->connected is set. 711 * On failure, we must add the command back to the 712 * issue queue so we can keep trying. 713 */ 714 /* 715 * REQUEST SENSE commands are issued without tagged 716 * queueing, even on SCSI-II devices because the 717 * contingent allegiance condition exists for the 718 * entire unit. 719 */ 720 721 if (!NCR5380_select(instance, cmd)) { 722 dsprintk(NDEBUG_MAIN, instance, "main: select complete\n"); 723 } else { 724 dsprintk(NDEBUG_MAIN | NDEBUG_QUEUES, instance, 725 "main: select failed, returning %p to queue\n", cmd); 726 requeue_cmd(instance, cmd); 727 } 728 } 729 if (hostdata->connected && !hostdata->dma_len) { 730 dsprintk(NDEBUG_MAIN, instance, "main: performing information transfer\n"); 731 NCR5380_information_transfer(instance); 732 done = 0; 733 } 734 if (!hostdata->connected) { 735 NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask); 736 maybe_release_dma_irq(instance); 737 } 738 spin_unlock_irq(&hostdata->lock); 739 if (!done) 740 cond_resched(); 741 } while (!done); 742} 743 744/* 745 * NCR5380_dma_complete - finish DMA transfer 746 * @instance: the scsi host instance 747 * 748 * Called by the interrupt handler when DMA finishes or a phase 749 * mismatch occurs (which would end the DMA transfer). 750 */ 751 752static void NCR5380_dma_complete(struct Scsi_Host *instance) 753{ 754 struct NCR5380_hostdata *hostdata = shost_priv(instance); 755 struct NCR5380_cmd *ncmd = NCR5380_to_ncmd(hostdata->connected); 756 int transferred; 757 unsigned char **data; 758 int *count; 759 int saved_data = 0, overrun = 0; 760 unsigned char p; 761 762 if (hostdata->read_overruns) { 763 p = ncmd->phase; 764 if (p & SR_IO) { 765 udelay(10); 766 if ((NCR5380_read(BUS_AND_STATUS_REG) & 767 (BASR_PHASE_MATCH | BASR_ACK)) == 768 (BASR_PHASE_MATCH | BASR_ACK)) { 769 saved_data = NCR5380_read(INPUT_DATA_REG); 770 overrun = 1; 771 dsprintk(NDEBUG_DMA, instance, "read overrun handled\n"); 772 } 773 } 774 } 775 776#ifdef CONFIG_SUN3 777 if (sun3scsi_dma_finish(hostdata->connected->sc_data_direction)) { 778 pr_err("scsi%d: overrun in UDC counter -- not prepared to deal with this!\n", 779 instance->host_no); 780 BUG(); 781 } 782 783 if ((NCR5380_read(BUS_AND_STATUS_REG) & (BASR_PHASE_MATCH | BASR_ACK)) == 784 (BASR_PHASE_MATCH | BASR_ACK)) { 785 pr_err("scsi%d: BASR %02x\n", instance->host_no, 786 NCR5380_read(BUS_AND_STATUS_REG)); 787 pr_err("scsi%d: bus stuck in data phase -- probably a single byte overrun!\n", 788 instance->host_no); 789 BUG(); 790 } 791#endif 792 793 NCR5380_write(MODE_REG, MR_BASE); 794 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 795 NCR5380_read(RESET_PARITY_INTERRUPT_REG); 796 797 transferred = hostdata->dma_len - NCR5380_dma_residual(hostdata); 798 hostdata->dma_len = 0; 799 800 data = (unsigned char **)&ncmd->ptr; 801 count = &ncmd->this_residual; 802 *data += transferred; 803 *count -= transferred; 804 805 if (hostdata->read_overruns) { 806 int cnt, toPIO; 807 808 if ((NCR5380_read(STATUS_REG) & PHASE_MASK) == p && (p & SR_IO)) { 809 cnt = toPIO = hostdata->read_overruns; 810 if (overrun) { 811 dsprintk(NDEBUG_DMA, instance, 812 "Got an input overrun, using saved byte\n"); 813 *(*data)++ = saved_data; 814 (*count)--; 815 cnt--; 816 toPIO--; 817 } 818 if (toPIO > 0) { 819 dsprintk(NDEBUG_DMA, instance, 820 "Doing %d byte PIO to 0x%p\n", cnt, *data); 821 NCR5380_transfer_pio(instance, &p, &cnt, data, 0); 822 *count -= toPIO - cnt; 823 } 824 } 825 } 826} 827 828/** 829 * NCR5380_intr - generic NCR5380 irq handler 830 * @irq: interrupt number 831 * @dev_id: device info 832 * 833 * Handle interrupts, reestablishing I_T_L or I_T_L_Q nexuses 834 * from the disconnected queue, and restarting NCR5380_main() 835 * as required. 836 * 837 * The chip can assert IRQ in any of six different conditions. The IRQ flag 838 * is then cleared by reading the Reset Parity/Interrupt Register (RPIR). 839 * Three of these six conditions are latched in the Bus and Status Register: 840 * - End of DMA (cleared by ending DMA Mode) 841 * - Parity error (cleared by reading RPIR) 842 * - Loss of BSY (cleared by reading RPIR) 843 * Two conditions have flag bits that are not latched: 844 * - Bus phase mismatch (non-maskable in DMA Mode, cleared by ending DMA Mode) 845 * - Bus reset (non-maskable) 846 * The remaining condition has no flag bit at all: 847 * - Selection/reselection 848 * 849 * Hence, establishing the cause(s) of any interrupt is partly guesswork. 850 * In "The DP8490 and DP5380 Comparison Guide", National Semiconductor 851 * claimed that "the design of the [DP8490] interrupt logic ensures 852 * interrupts will not be lost (they can be on the DP5380)." 853 * The L5380/53C80 datasheet from LOGIC Devices has more details. 854 * 855 * Checking for bus reset by reading RST is futile because of interrupt 856 * latency, but a bus reset will reset chip logic. Checking for parity error 857 * is unnecessary because that interrupt is never enabled. A Loss of BSY 858 * condition will clear DMA Mode. We can tell when this occurs because the 859 * Busy Monitor interrupt is enabled together with DMA Mode. 860 */ 861 862static irqreturn_t __maybe_unused NCR5380_intr(int irq, void *dev_id) 863{ 864 struct Scsi_Host *instance = dev_id; 865 struct NCR5380_hostdata *hostdata = shost_priv(instance); 866 int handled = 0; 867 unsigned char basr; 868 unsigned long flags; 869 870 spin_lock_irqsave(&hostdata->lock, flags); 871 872 basr = NCR5380_read(BUS_AND_STATUS_REG); 873 if (basr & BASR_IRQ) { 874 unsigned char mr = NCR5380_read(MODE_REG); 875 unsigned char sr = NCR5380_read(STATUS_REG); 876 877 dsprintk(NDEBUG_INTR, instance, "IRQ %d, BASR 0x%02x, SR 0x%02x, MR 0x%02x\n", 878 irq, basr, sr, mr); 879 880 if ((mr & MR_DMA_MODE) || (mr & MR_MONITOR_BSY)) { 881 /* Probably End of DMA, Phase Mismatch or Loss of BSY. 882 * We ack IRQ after clearing Mode Register. Workarounds 883 * for End of DMA errata need to happen in DMA Mode. 884 */ 885 886 dsprintk(NDEBUG_INTR, instance, "interrupt in DMA mode\n"); 887 888 if (hostdata->connected) { 889 NCR5380_dma_complete(instance); 890 queue_work(hostdata->work_q, &hostdata->main_task); 891 } else { 892 NCR5380_write(MODE_REG, MR_BASE); 893 NCR5380_read(RESET_PARITY_INTERRUPT_REG); 894 } 895 } else if ((NCR5380_read(CURRENT_SCSI_DATA_REG) & hostdata->id_mask) && 896 (sr & (SR_SEL | SR_IO | SR_BSY | SR_RST)) == (SR_SEL | SR_IO)) { 897 /* Probably reselected */ 898 NCR5380_write(SELECT_ENABLE_REG, 0); 899 NCR5380_read(RESET_PARITY_INTERRUPT_REG); 900 901 dsprintk(NDEBUG_INTR, instance, "interrupt with SEL and IO\n"); 902 903 if (!hostdata->connected) { 904 NCR5380_reselect(instance); 905 queue_work(hostdata->work_q, &hostdata->main_task); 906 } 907 if (!hostdata->connected) 908 NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask); 909 } else { 910 /* Probably Bus Reset */ 911 NCR5380_read(RESET_PARITY_INTERRUPT_REG); 912 913 if (sr & SR_RST) { 914 /* Certainly Bus Reset */ 915 shost_printk(KERN_WARNING, instance, 916 "bus reset interrupt\n"); 917 bus_reset_cleanup(instance); 918 } else { 919 dsprintk(NDEBUG_INTR, instance, "unknown interrupt\n"); 920 } 921#ifdef SUN3_SCSI_VME 922 dregs->csr |= CSR_DMA_ENABLE; 923#endif 924 } 925 handled = 1; 926 } else { 927 dsprintk(NDEBUG_INTR, instance, "interrupt without IRQ bit\n"); 928#ifdef SUN3_SCSI_VME 929 dregs->csr |= CSR_DMA_ENABLE; 930#endif 931 } 932 933 spin_unlock_irqrestore(&hostdata->lock, flags); 934 935 return IRQ_RETVAL(handled); 936} 937 938/** 939 * NCR5380_select - attempt arbitration and selection for a given command 940 * @instance: the Scsi_Host instance 941 * @cmd: the scsi_cmnd to execute 942 * 943 * This routine establishes an I_T_L nexus for a SCSI command. This involves 944 * ARBITRATION, SELECTION and MESSAGE OUT phases and an IDENTIFY message. 945 * 946 * Returns true if the operation should be retried. 947 * Returns false if it should not be retried. 948 * 949 * Side effects : 950 * If bus busy, arbitration failed, etc, NCR5380_select() will exit 951 * with registers as they should have been on entry - ie 952 * SELECT_ENABLE will be set appropriately, the NCR5380 953 * will cease to drive any SCSI bus signals. 954 * 955 * If successful : the I_T_L nexus will be established, and 956 * hostdata->connected will be set to cmd. 957 * SELECT interrupt will be disabled. 958 * 959 * If failed (no target) : scsi_done() will be called, and the 960 * cmd->result host byte set to DID_BAD_TARGET. 961 */ 962 963static bool NCR5380_select(struct Scsi_Host *instance, struct scsi_cmnd *cmd) 964 __releases(&hostdata->lock) __acquires(&hostdata->lock) 965{ 966 struct NCR5380_hostdata *hostdata = shost_priv(instance); 967 unsigned char tmp[3], phase; 968 unsigned char *data; 969 int len; 970 int err; 971 bool ret = true; 972 bool can_disconnect = instance->irq != NO_IRQ && 973 cmd->cmnd[0] != REQUEST_SENSE && 974 (disconnect_mask & BIT(scmd_id(cmd))); 975 976 NCR5380_dprint(NDEBUG_ARBITRATION, instance); 977 dsprintk(NDEBUG_ARBITRATION, instance, "starting arbitration, id = %d\n", 978 instance->this_id); 979 980 /* 981 * Arbitration and selection phases are slow and involve dropping the 982 * lock, so we have to watch out for EH. An exception handler may 983 * change 'selecting' to NULL. This function will then return false 984 * so that the caller will forget about 'cmd'. (During information 985 * transfer phases, EH may change 'connected' to NULL.) 986 */ 987 hostdata->selecting = cmd; 988 989 /* 990 * Set the phase bits to 0, otherwise the NCR5380 won't drive the 991 * data bus during SELECTION. 992 */ 993 994 NCR5380_write(TARGET_COMMAND_REG, 0); 995 996 /* 997 * Start arbitration. 998 */ 999 1000 NCR5380_write(OUTPUT_DATA_REG, hostdata->id_mask); 1001 NCR5380_write(MODE_REG, MR_ARBITRATE); 1002 1003 /* The chip now waits for BUS FREE phase. Then after the 800 ns 1004 * Bus Free Delay, arbitration will begin. 1005 */ 1006 1007 spin_unlock_irq(&hostdata->lock); 1008 err = NCR5380_poll_politely2(hostdata, MODE_REG, MR_ARBITRATE, 0, 1009 INITIATOR_COMMAND_REG, ICR_ARBITRATION_PROGRESS, 1010 ICR_ARBITRATION_PROGRESS, HZ); 1011 spin_lock_irq(&hostdata->lock); 1012 if (!(NCR5380_read(MODE_REG) & MR_ARBITRATE)) { 1013 /* Reselection interrupt */ 1014 goto out; 1015 } 1016 if (!hostdata->selecting) { 1017 /* Command was aborted */ 1018 NCR5380_write(MODE_REG, MR_BASE); 1019 return false; 1020 } 1021 if (err < 0) { 1022 NCR5380_write(MODE_REG, MR_BASE); 1023 shost_printk(KERN_ERR, instance, 1024 "select: arbitration timeout\n"); 1025 goto out; 1026 } 1027 spin_unlock_irq(&hostdata->lock); 1028 1029 /* The SCSI-2 arbitration delay is 2.4 us */ 1030 udelay(3); 1031 1032 /* Check for lost arbitration */ 1033 if ((NCR5380_read(INITIATOR_COMMAND_REG) & ICR_ARBITRATION_LOST) || 1034 (NCR5380_read(CURRENT_SCSI_DATA_REG) & hostdata->id_higher_mask) || 1035 (NCR5380_read(INITIATOR_COMMAND_REG) & ICR_ARBITRATION_LOST)) { 1036 NCR5380_write(MODE_REG, MR_BASE); 1037 dsprintk(NDEBUG_ARBITRATION, instance, "lost arbitration, deasserting MR_ARBITRATE\n"); 1038 spin_lock_irq(&hostdata->lock); 1039 goto out; 1040 } 1041 1042 /* After/during arbitration, BSY should be asserted. 1043 * IBM DPES-31080 Version S31Q works now 1044 * Tnx to Thomas_Roesch@m2.maus.de for finding this! (Roman) 1045 */ 1046 NCR5380_write(INITIATOR_COMMAND_REG, 1047 ICR_BASE | ICR_ASSERT_SEL | ICR_ASSERT_BSY); 1048 1049 /* 1050 * Again, bus clear + bus settle time is 1.2us, however, this is 1051 * a minimum so we'll udelay ceil(1.2) 1052 */ 1053 1054 if (hostdata->flags & FLAG_TOSHIBA_DELAY) 1055 udelay(15); 1056 else 1057 udelay(2); 1058 1059 spin_lock_irq(&hostdata->lock); 1060 1061 /* NCR5380_reselect() clears MODE_REG after a reselection interrupt */ 1062 if (!(NCR5380_read(MODE_REG) & MR_ARBITRATE)) 1063 goto out; 1064 1065 if (!hostdata->selecting) { 1066 NCR5380_write(MODE_REG, MR_BASE); 1067 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 1068 return false; 1069 } 1070 1071 dsprintk(NDEBUG_ARBITRATION, instance, "won arbitration\n"); 1072 1073 /* 1074 * Now that we have won arbitration, start Selection process, asserting 1075 * the host and target ID's on the SCSI bus. 1076 */ 1077 1078 NCR5380_write(OUTPUT_DATA_REG, hostdata->id_mask | (1 << scmd_id(cmd))); 1079 1080 /* 1081 * Raise ATN while SEL is true before BSY goes false from arbitration, 1082 * since this is the only way to guarantee that we'll get a MESSAGE OUT 1083 * phase immediately after selection. 1084 */ 1085 1086 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_BSY | 1087 ICR_ASSERT_DATA | ICR_ASSERT_ATN | ICR_ASSERT_SEL); 1088 NCR5380_write(MODE_REG, MR_BASE); 1089 1090 /* 1091 * Reselect interrupts must be turned off prior to the dropping of BSY, 1092 * otherwise we will trigger an interrupt. 1093 */ 1094 NCR5380_write(SELECT_ENABLE_REG, 0); 1095 1096 spin_unlock_irq(&hostdata->lock); 1097 1098 /* 1099 * The initiator shall then wait at least two deskew delays and release 1100 * the BSY signal. 1101 */ 1102 udelay(1); /* wingel -- wait two bus deskew delay >2*45ns */ 1103 1104 /* Reset BSY */ 1105 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA | 1106 ICR_ASSERT_ATN | ICR_ASSERT_SEL); 1107 1108 /* 1109 * Something weird happens when we cease to drive BSY - looks 1110 * like the board/chip is letting us do another read before the 1111 * appropriate propagation delay has expired, and we're confusing 1112 * a BSY signal from ourselves as the target's response to SELECTION. 1113 * 1114 * A small delay (the 'C++' frontend breaks the pipeline with an 1115 * unnecessary jump, making it work on my 386-33/Trantor T128, the 1116 * tighter 'C' code breaks and requires this) solves the problem - 1117 * the 1 us delay is arbitrary, and only used because this delay will 1118 * be the same on other platforms and since it works here, it should 1119 * work there. 1120 * 1121 * wingel suggests that this could be due to failing to wait 1122 * one deskew delay. 1123 */ 1124 1125 udelay(1); 1126 1127 dsprintk(NDEBUG_SELECTION, instance, "selecting target %d\n", scmd_id(cmd)); 1128 1129 /* 1130 * The SCSI specification calls for a 250 ms timeout for the actual 1131 * selection. 1132 */ 1133 1134 err = NCR5380_poll_politely(hostdata, STATUS_REG, SR_BSY, SR_BSY, 1135 msecs_to_jiffies(250)); 1136 1137 if ((NCR5380_read(STATUS_REG) & (SR_SEL | SR_IO)) == (SR_SEL | SR_IO)) { 1138 spin_lock_irq(&hostdata->lock); 1139 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 1140 NCR5380_reselect(instance); 1141 shost_printk(KERN_ERR, instance, "reselection after won arbitration?\n"); 1142 goto out; 1143 } 1144 1145 if (err < 0) { 1146 spin_lock_irq(&hostdata->lock); 1147 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 1148 1149 /* Can't touch cmd if it has been reclaimed by the scsi ML */ 1150 if (!hostdata->selecting) 1151 return false; 1152 1153 cmd->result = DID_BAD_TARGET << 16; 1154 complete_cmd(instance, cmd); 1155 dsprintk(NDEBUG_SELECTION, instance, 1156 "target did not respond within 250ms\n"); 1157 ret = false; 1158 goto out; 1159 } 1160 1161 /* 1162 * No less than two deskew delays after the initiator detects the 1163 * BSY signal is true, it shall release the SEL signal and may 1164 * change the DATA BUS. -wingel 1165 */ 1166 1167 udelay(1); 1168 1169 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN); 1170 1171 /* 1172 * Since we followed the SCSI spec, and raised ATN while SEL 1173 * was true but before BSY was false during selection, the information 1174 * transfer phase should be a MESSAGE OUT phase so that we can send the 1175 * IDENTIFY message. 1176 */ 1177 1178 /* Wait for start of REQ/ACK handshake */ 1179 1180 err = NCR5380_poll_politely(hostdata, STATUS_REG, SR_REQ, SR_REQ, HZ); 1181 spin_lock_irq(&hostdata->lock); 1182 if (err < 0) { 1183 shost_printk(KERN_ERR, instance, "select: REQ timeout\n"); 1184 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 1185 goto out; 1186 } 1187 if (!hostdata->selecting) { 1188 do_abort(instance, 0); 1189 return false; 1190 } 1191 1192 dsprintk(NDEBUG_SELECTION, instance, "target %d selected, going into MESSAGE OUT phase.\n", 1193 scmd_id(cmd)); 1194 tmp[0] = IDENTIFY(can_disconnect, cmd->device->lun); 1195 1196 len = 1; 1197 data = tmp; 1198 phase = PHASE_MSGOUT; 1199 NCR5380_transfer_pio(instance, &phase, &len, &data, 0); 1200 if (len) { 1201 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 1202 cmd->result = DID_ERROR << 16; 1203 complete_cmd(instance, cmd); 1204 dsprintk(NDEBUG_SELECTION, instance, "IDENTIFY message transfer failed\n"); 1205 ret = false; 1206 goto out; 1207 } 1208 1209 dsprintk(NDEBUG_SELECTION, instance, "nexus established.\n"); 1210 1211 hostdata->connected = cmd; 1212 hostdata->busy[cmd->device->id] |= 1 << cmd->device->lun; 1213 1214#ifdef SUN3_SCSI_VME 1215 dregs->csr |= CSR_INTR; 1216#endif 1217 1218 initialize_SCp(cmd); 1219 1220 ret = false; 1221 1222out: 1223 if (!hostdata->selecting) 1224 return false; 1225 hostdata->selecting = NULL; 1226 return ret; 1227} 1228 1229/** 1230 * NCR5380_transfer_pio() - transfers data in given phase using polled I/O 1231 * @instance: instance of driver 1232 * @phase: pointer to what phase is expected 1233 * @count: pointer to number of bytes to transfer 1234 * @data: pointer to data pointer 1235 * @can_sleep: 1 or 0 when sleeping is permitted or not, respectively 1236 * 1237 * Returns: void. *phase, *count, *data are modified in place. 1238 */ 1239 1240/* 1241 * Note : this code is not as quick as it could be, however it 1242 * IS 100% reliable, and for the actual data transfer where speed 1243 * counts, we will always do a pseudo DMA or DMA transfer. 1244 */ 1245 1246static void NCR5380_transfer_pio(struct Scsi_Host *instance, 1247 unsigned char *phase, int *count, 1248 unsigned char **data, unsigned int can_sleep) 1249{ 1250 struct NCR5380_hostdata *hostdata = shost_priv(instance); 1251 unsigned char p = *phase, tmp; 1252 int c = *count; 1253 unsigned char *d = *data; 1254 1255 /* 1256 * The NCR5380 chip will only drive the SCSI bus when the 1257 * phase specified in the appropriate bits of the TARGET COMMAND 1258 * REGISTER match the STATUS REGISTER 1259 */ 1260 1261 NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p)); 1262 1263 do { 1264 /* 1265 * Wait for assertion of REQ, after which the phase bits will be 1266 * valid 1267 */ 1268 1269 if (NCR5380_poll_politely(hostdata, STATUS_REG, SR_REQ | SR_BSY, 1270 SR_REQ | SR_BSY, HZ * can_sleep) < 0) 1271 break; 1272 1273 dsprintk(NDEBUG_HANDSHAKE, instance, "REQ asserted\n"); 1274 1275 /* Check for phase mismatch */ 1276 if ((NCR5380_read(STATUS_REG) & PHASE_MASK) != p) { 1277 dsprintk(NDEBUG_PIO, instance, "phase mismatch\n"); 1278 NCR5380_dprint_phase(NDEBUG_PIO, instance); 1279 break; 1280 } 1281 1282 /* Do actual transfer from SCSI bus to / from memory */ 1283 if (!(p & SR_IO)) 1284 NCR5380_write(OUTPUT_DATA_REG, *d); 1285 else 1286 *d = NCR5380_read(CURRENT_SCSI_DATA_REG); 1287 1288 ++d; 1289 1290 /* 1291 * The SCSI standard suggests that in MSGOUT phase, the initiator 1292 * should drop ATN on the last byte of the message phase 1293 * after REQ has been asserted for the handshake but before 1294 * the initiator raises ACK. 1295 */ 1296 1297 if (!(p & SR_IO)) { 1298 if (!((p & SR_MSG) && c > 1)) { 1299 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA); 1300 NCR5380_dprint(NDEBUG_PIO, instance); 1301 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | 1302 ICR_ASSERT_DATA | ICR_ASSERT_ACK); 1303 } else { 1304 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | 1305 ICR_ASSERT_DATA | ICR_ASSERT_ATN); 1306 NCR5380_dprint(NDEBUG_PIO, instance); 1307 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | 1308 ICR_ASSERT_DATA | ICR_ASSERT_ATN | ICR_ASSERT_ACK); 1309 } 1310 } else { 1311 NCR5380_dprint(NDEBUG_PIO, instance); 1312 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ACK); 1313 } 1314 1315 if (NCR5380_poll_politely(hostdata, 1316 STATUS_REG, SR_REQ, 0, 5 * HZ * can_sleep) < 0) 1317 break; 1318 1319 dsprintk(NDEBUG_HANDSHAKE, instance, "REQ negated, handshake complete\n"); 1320 1321 /* 1322 * We have several special cases to consider during REQ/ACK 1323 * handshaking: 1324 * 1325 * 1. We were in MSGOUT phase, and we are on the last byte of 1326 * the message. ATN must be dropped as ACK is dropped. 1327 * 1328 * 2. We are in MSGIN phase, and we are on the last byte of the 1329 * message. We must exit with ACK asserted, so that the calling 1330 * code may raise ATN before dropping ACK to reject the message. 1331 * 1332 * 3. ACK and ATN are clear & the target may proceed as normal. 1333 */ 1334 if (!(p == PHASE_MSGIN && c == 1)) { 1335 if (p == PHASE_MSGOUT && c > 1) 1336 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN); 1337 else 1338 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 1339 } 1340 } while (--c); 1341 1342 dsprintk(NDEBUG_PIO, instance, "residual %d\n", c); 1343 1344 *count = c; 1345 *data = d; 1346 tmp = NCR5380_read(STATUS_REG); 1347 /* The phase read from the bus is valid if either REQ is (already) 1348 * asserted or if ACK hasn't been released yet. The latter applies if 1349 * we're in MSG IN, DATA IN or STATUS and all bytes have been received. 1350 */ 1351 if ((tmp & SR_REQ) || ((tmp & SR_IO) && c == 0)) 1352 *phase = tmp & PHASE_MASK; 1353 else 1354 *phase = PHASE_UNKNOWN; 1355} 1356 1357/** 1358 * do_reset - issue a reset command 1359 * @instance: adapter to reset 1360 * 1361 * Issue a reset sequence to the NCR5380 and try and get the bus 1362 * back into sane shape. 1363 * 1364 * This clears the reset interrupt flag because there may be no handler for 1365 * it. When the driver is initialized, the NCR5380_intr() handler has not yet 1366 * been installed. And when in EH we may have released the ST DMA interrupt. 1367 */ 1368 1369static void do_reset(struct Scsi_Host *instance) 1370{ 1371 struct NCR5380_hostdata __maybe_unused *hostdata = shost_priv(instance); 1372 unsigned long flags; 1373 1374 local_irq_save(flags); 1375 NCR5380_write(TARGET_COMMAND_REG, 1376 PHASE_SR_TO_TCR(NCR5380_read(STATUS_REG) & PHASE_MASK)); 1377 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_RST); 1378 udelay(50); 1379 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 1380 (void)NCR5380_read(RESET_PARITY_INTERRUPT_REG); 1381 local_irq_restore(flags); 1382} 1383 1384/** 1385 * do_abort - abort the currently established nexus by going to 1386 * MESSAGE OUT phase and sending an ABORT message. 1387 * @instance: relevant scsi host instance 1388 * @can_sleep: 1 or 0 when sleeping is permitted or not, respectively 1389 * 1390 * Returns 0 on success, negative error code on failure. 1391 */ 1392 1393static int do_abort(struct Scsi_Host *instance, unsigned int can_sleep) 1394{ 1395 struct NCR5380_hostdata *hostdata = shost_priv(instance); 1396 unsigned char *msgptr, phase, tmp; 1397 int len; 1398 int rc; 1399 1400 /* Request message out phase */ 1401 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN); 1402 1403 /* 1404 * Wait for the target to indicate a valid phase by asserting 1405 * REQ. Once this happens, we'll have either a MSGOUT phase 1406 * and can immediately send the ABORT message, or we'll have some 1407 * other phase and will have to source/sink data. 1408 * 1409 * We really don't care what value was on the bus or what value 1410 * the target sees, so we just handshake. 1411 */ 1412 1413 rc = NCR5380_poll_politely(hostdata, STATUS_REG, SR_REQ, SR_REQ, 1414 10 * HZ * can_sleep); 1415 if (rc < 0) 1416 goto out; 1417 1418 tmp = NCR5380_read(STATUS_REG) & PHASE_MASK; 1419 1420 NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(tmp)); 1421 1422 if (tmp != PHASE_MSGOUT) { 1423 NCR5380_write(INITIATOR_COMMAND_REG, 1424 ICR_BASE | ICR_ASSERT_ATN | ICR_ASSERT_ACK); 1425 rc = NCR5380_poll_politely(hostdata, STATUS_REG, SR_REQ, 0, 1426 3 * HZ * can_sleep); 1427 if (rc < 0) 1428 goto out; 1429 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN); 1430 } 1431 1432 tmp = ABORT; 1433 msgptr = &tmp; 1434 len = 1; 1435 phase = PHASE_MSGOUT; 1436 NCR5380_transfer_pio(instance, &phase, &len, &msgptr, can_sleep); 1437 if (len) 1438 rc = -ENXIO; 1439 1440 /* 1441 * If we got here, and the command completed successfully, 1442 * we're about to go into bus free state. 1443 */ 1444 1445out: 1446 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 1447 return rc; 1448} 1449 1450/* 1451 * Function : int NCR5380_transfer_dma (struct Scsi_Host *instance, 1452 * unsigned char *phase, int *count, unsigned char **data) 1453 * 1454 * Purpose : transfers data in given phase using either real 1455 * or pseudo DMA. 1456 * 1457 * Inputs : instance - instance of driver, *phase - pointer to 1458 * what phase is expected, *count - pointer to number of 1459 * bytes to transfer, **data - pointer to data pointer. 1460 * 1461 * Returns : -1 when different phase is entered without transferring 1462 * maximum number of bytes, 0 if all bytes or transferred or exit 1463 * is in same phase. 1464 * 1465 * Also, *phase, *count, *data are modified in place. 1466 */ 1467 1468 1469static int NCR5380_transfer_dma(struct Scsi_Host *instance, 1470 unsigned char *phase, int *count, 1471 unsigned char **data) 1472{ 1473 struct NCR5380_hostdata *hostdata = shost_priv(instance); 1474 struct NCR5380_cmd *ncmd = NCR5380_to_ncmd(hostdata->connected); 1475 int c = *count; 1476 unsigned char p = *phase; 1477 unsigned char *d = *data; 1478 unsigned char tmp; 1479 int result = 0; 1480 1481 if ((tmp = (NCR5380_read(STATUS_REG) & PHASE_MASK)) != p) { 1482 *phase = tmp; 1483 return -1; 1484 } 1485 1486 ncmd->phase = p; 1487 1488 if (p & SR_IO) { 1489 if (hostdata->read_overruns) 1490 c -= hostdata->read_overruns; 1491 else if (hostdata->flags & FLAG_DMA_FIXUP) 1492 --c; 1493 } 1494 1495 dsprintk(NDEBUG_DMA, instance, "initializing DMA %s: length %d, address %p\n", 1496 (p & SR_IO) ? "receive" : "send", c, d); 1497 1498#ifdef CONFIG_SUN3 1499 /* send start chain */ 1500 sun3scsi_dma_start(c, *data); 1501#endif 1502 1503 NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p)); 1504 NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY | 1505 MR_ENABLE_EOP_INTR); 1506 1507 if (!(hostdata->flags & FLAG_LATE_DMA_SETUP)) { 1508 /* On the Medusa, it is a must to initialize the DMA before 1509 * starting the NCR. This is also the cleaner way for the TT. 1510 */ 1511 if (p & SR_IO) 1512 result = NCR5380_dma_recv_setup(hostdata, d, c); 1513 else 1514 result = NCR5380_dma_send_setup(hostdata, d, c); 1515 } 1516 1517 /* 1518 * On the PAS16 at least I/O recovery delays are not needed here. 1519 * Everyone else seems to want them. 1520 */ 1521 1522 if (p & SR_IO) { 1523 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 1524 NCR5380_io_delay(1); 1525 NCR5380_write(START_DMA_INITIATOR_RECEIVE_REG, 0); 1526 } else { 1527 NCR5380_io_delay(1); 1528 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA); 1529 NCR5380_io_delay(1); 1530 NCR5380_write(START_DMA_SEND_REG, 0); 1531 NCR5380_io_delay(1); 1532 } 1533 1534#ifdef CONFIG_SUN3 1535#ifdef SUN3_SCSI_VME 1536 dregs->csr |= CSR_DMA_ENABLE; 1537#endif 1538 sun3_dma_active = 1; 1539#endif 1540 1541 if (hostdata->flags & FLAG_LATE_DMA_SETUP) { 1542 /* On the Falcon, the DMA setup must be done after the last 1543 * NCR access, else the DMA setup gets trashed! 1544 */ 1545 if (p & SR_IO) 1546 result = NCR5380_dma_recv_setup(hostdata, d, c); 1547 else 1548 result = NCR5380_dma_send_setup(hostdata, d, c); 1549 } 1550 1551 /* On failure, NCR5380_dma_xxxx_setup() returns a negative int. */ 1552 if (result < 0) 1553 return result; 1554 1555 /* For real DMA, result is the byte count. DMA interrupt is expected. */ 1556 if (result > 0) { 1557 hostdata->dma_len = result; 1558 return 0; 1559 } 1560 1561 /* The result is zero iff pseudo DMA send/receive was completed. */ 1562 hostdata->dma_len = c; 1563 1564 /* 1565 * A note regarding the DMA errata workarounds for early NMOS silicon. 1566 * 1567 * For DMA sends, we want to wait until the last byte has been 1568 * transferred out over the bus before we turn off DMA mode. Alas, there 1569 * seems to be no terribly good way of doing this on a 5380 under all 1570 * conditions. For non-scatter-gather operations, we can wait until REQ 1571 * and ACK both go false, or until a phase mismatch occurs. Gather-sends 1572 * are nastier, since the device will be expecting more data than we 1573 * are prepared to send it, and REQ will remain asserted. On a 53C8[01] 1574 * we could test Last Byte Sent to assure transfer (I imagine this is 1575 * precisely why this signal was added to the newer chips) but on the 1576 * older 538[01] this signal does not exist. The workaround for this 1577 * lack is a watchdog; we bail out of the wait-loop after a modest 1578 * amount of wait-time if the usual exit conditions are not met. 1579 * Not a terribly clean or correct solution :-% 1580 * 1581 * DMA receive is equally tricky due to a nasty characteristic of the 1582 * NCR5380. If the chip is in DMA receive mode, it will respond to a 1583 * target's REQ by latching the SCSI data into the INPUT DATA register 1584 * and asserting ACK, even if it has _already_ been notified by the 1585 * DMA controller that the current DMA transfer has completed! If the 1586 * NCR5380 is then taken out of DMA mode, this already-acknowledged 1587 * byte is lost. 1588 * 1589 * This is not a problem for "one DMA transfer per READ 1590 * command", because the situation will never arise... either all of 1591 * the data is DMA'ed properly, or the target switches to MESSAGE IN 1592 * phase to signal a disconnection (either operation bringing the DMA 1593 * to a clean halt). However, in order to handle scatter-receive, we 1594 * must work around the problem. The chosen fix is to DMA fewer bytes, 1595 * then check for the condition before taking the NCR5380 out of DMA 1596 * mode. One or two extra bytes are transferred via PIO as necessary 1597 * to fill out the original request. 1598 */ 1599 1600 if ((hostdata->flags & FLAG_DMA_FIXUP) && 1601 (NCR5380_read(BUS_AND_STATUS_REG) & BASR_PHASE_MATCH)) { 1602 /* 1603 * The workaround was to transfer fewer bytes than we 1604 * intended to with the pseudo-DMA receive function, wait for 1605 * the chip to latch the last byte, read it, and then disable 1606 * DMA mode. 1607 * 1608 * After REQ is asserted, the NCR5380 asserts DRQ and ACK. 1609 * REQ is deasserted when ACK is asserted, and not reasserted 1610 * until ACK goes false. Since the NCR5380 won't lower ACK 1611 * until DACK is asserted, which won't happen unless we twiddle 1612 * the DMA port or we take the NCR5380 out of DMA mode, we 1613 * can guarantee that we won't handshake another extra 1614 * byte. 1615 * 1616 * If sending, wait for the last byte to be sent. If REQ is 1617 * being asserted for the byte we're interested, we'll ACK it 1618 * and it will go false. 1619 */ 1620 if (!NCR5380_poll_politely(hostdata, BUS_AND_STATUS_REG, 1621 BASR_DRQ, BASR_DRQ, 0)) { 1622 if ((p & SR_IO) && 1623 (NCR5380_read(BUS_AND_STATUS_REG) & BASR_PHASE_MATCH)) { 1624 if (!NCR5380_poll_politely(hostdata, STATUS_REG, 1625 SR_REQ, 0, 0)) { 1626 d[c] = NCR5380_read(INPUT_DATA_REG); 1627 --ncmd->this_residual; 1628 } else { 1629 result = -1; 1630 scmd_printk(KERN_ERR, hostdata->connected, 1631 "PDMA fixup: !REQ timeout\n"); 1632 } 1633 } 1634 } else if (NCR5380_read(BUS_AND_STATUS_REG) & BASR_PHASE_MATCH) { 1635 result = -1; 1636 scmd_printk(KERN_ERR, hostdata->connected, 1637 "PDMA fixup: DRQ timeout\n"); 1638 } 1639 } 1640 1641 NCR5380_dma_complete(instance); 1642 return result; 1643} 1644 1645/* 1646 * Function : NCR5380_information_transfer (struct Scsi_Host *instance) 1647 * 1648 * Purpose : run through the various SCSI phases and do as the target 1649 * directs us to. Operates on the currently connected command, 1650 * instance->connected. 1651 * 1652 * Inputs : instance, instance for which we are doing commands 1653 * 1654 * Side effects : SCSI things happen, the disconnected queue will be 1655 * modified if a command disconnects, *instance->connected will 1656 * change. 1657 */ 1658 1659static void NCR5380_information_transfer(struct Scsi_Host *instance) 1660 __releases(&hostdata->lock) __acquires(&hostdata->lock) 1661{ 1662 struct NCR5380_hostdata *hostdata = shost_priv(instance); 1663 unsigned char msgout = NOP; 1664 int sink = 0; 1665 int len; 1666 int transfersize; 1667 unsigned char *data; 1668 unsigned char phase, tmp, extended_msg[10], old_phase = 0xff; 1669 struct scsi_cmnd *cmd; 1670 1671#ifdef SUN3_SCSI_VME 1672 dregs->csr |= CSR_INTR; 1673#endif 1674 1675 while ((cmd = hostdata->connected)) { 1676 struct NCR5380_cmd *ncmd = NCR5380_to_ncmd(cmd); 1677 1678 tmp = NCR5380_read(STATUS_REG); 1679 /* We only have a valid SCSI phase when REQ is asserted */ 1680 if (tmp & SR_REQ) { 1681 phase = (tmp & PHASE_MASK); 1682 if (phase != old_phase) { 1683 old_phase = phase; 1684 NCR5380_dprint_phase(NDEBUG_INFORMATION, instance); 1685 } 1686#ifdef CONFIG_SUN3 1687 if (phase == PHASE_CMDOUT && 1688 sun3_dma_setup_done != cmd) { 1689 int count; 1690 1691 advance_sg_buffer(ncmd); 1692 1693 count = sun3scsi_dma_xfer_len(hostdata, cmd); 1694 1695 if (count > 0) { 1696 if (cmd->sc_data_direction == DMA_TO_DEVICE) 1697 sun3scsi_dma_send_setup(hostdata, 1698 ncmd->ptr, count); 1699 else 1700 sun3scsi_dma_recv_setup(hostdata, 1701 ncmd->ptr, count); 1702 sun3_dma_setup_done = cmd; 1703 } 1704#ifdef SUN3_SCSI_VME 1705 dregs->csr |= CSR_INTR; 1706#endif 1707 } 1708#endif /* CONFIG_SUN3 */ 1709 1710 if (sink && (phase != PHASE_MSGOUT)) { 1711 NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(tmp)); 1712 1713 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN | 1714 ICR_ASSERT_ACK); 1715 while (NCR5380_read(STATUS_REG) & SR_REQ) 1716 ; 1717 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | 1718 ICR_ASSERT_ATN); 1719 sink = 0; 1720 continue; 1721 } 1722 1723 switch (phase) { 1724 case PHASE_DATAOUT: 1725#if (NDEBUG & NDEBUG_NO_DATAOUT) 1726 shost_printk(KERN_DEBUG, instance, "NDEBUG_NO_DATAOUT set, attempted DATAOUT aborted\n"); 1727 sink = 1; 1728 do_abort(instance, 0); 1729 cmd->result = DID_ERROR << 16; 1730 complete_cmd(instance, cmd); 1731 hostdata->connected = NULL; 1732 hostdata->busy[scmd_id(cmd)] &= ~(1 << cmd->device->lun); 1733 return; 1734#endif 1735 case PHASE_DATAIN: 1736 /* 1737 * If there is no room left in the current buffer in the 1738 * scatter-gather list, move onto the next one. 1739 */ 1740 1741 advance_sg_buffer(ncmd); 1742 dsprintk(NDEBUG_INFORMATION, instance, 1743 "this residual %d, sg ents %d\n", 1744 ncmd->this_residual, 1745 sg_nents(ncmd->buffer)); 1746 1747 /* 1748 * The preferred transfer method is going to be 1749 * PSEUDO-DMA for systems that are strictly PIO, 1750 * since we can let the hardware do the handshaking. 1751 * 1752 * For this to work, we need to know the transfersize 1753 * ahead of time, since the pseudo-DMA code will sit 1754 * in an unconditional loop. 1755 */ 1756 1757 transfersize = 0; 1758 if (!cmd->device->borken) 1759 transfersize = NCR5380_dma_xfer_len(hostdata, cmd); 1760 1761 if (transfersize > 0) { 1762 len = transfersize; 1763 if (NCR5380_transfer_dma(instance, &phase, 1764 &len, (unsigned char **)&ncmd->ptr)) { 1765 /* 1766 * If the watchdog timer fires, all future 1767 * accesses to this device will use the 1768 * polled-IO. 1769 */ 1770 scmd_printk(KERN_INFO, cmd, 1771 "switching to slow handshake\n"); 1772 cmd->device->borken = 1; 1773 do_reset(instance); 1774 bus_reset_cleanup(instance); 1775 } 1776 } else { 1777 /* Transfer a small chunk so that the 1778 * irq mode lock is not held too long. 1779 */ 1780 transfersize = min(ncmd->this_residual, 1781 NCR5380_PIO_CHUNK_SIZE); 1782 len = transfersize; 1783 NCR5380_transfer_pio(instance, &phase, &len, 1784 (unsigned char **)&ncmd->ptr, 1785 0); 1786 ncmd->this_residual -= transfersize - len; 1787 } 1788#ifdef CONFIG_SUN3 1789 if (sun3_dma_setup_done == cmd) 1790 sun3_dma_setup_done = NULL; 1791#endif 1792 return; 1793 case PHASE_MSGIN: 1794 len = 1; 1795 tmp = 0xff; 1796 data = &tmp; 1797 NCR5380_transfer_pio(instance, &phase, &len, &data, 0); 1798 if (tmp == 0xff) 1799 break; 1800 1801 switch (tmp) { 1802 case ABORT: 1803 set_host_byte(cmd, DID_ABORT); 1804 fallthrough; 1805 case COMMAND_COMPLETE: 1806 /* Accept message by clearing ACK */ 1807 sink = 1; 1808 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 1809 dsprintk(NDEBUG_QUEUES, instance, 1810 "COMMAND COMPLETE %p target %d lun %llu\n", 1811 cmd, scmd_id(cmd), cmd->device->lun); 1812 1813 hostdata->connected = NULL; 1814 hostdata->busy[scmd_id(cmd)] &= ~(1 << cmd->device->lun); 1815 1816 set_status_byte(cmd, ncmd->status); 1817 1818 set_resid_from_SCp(cmd); 1819 1820 if (cmd->cmnd[0] == REQUEST_SENSE) 1821 complete_cmd(instance, cmd); 1822 else { 1823 if (ncmd->status == SAM_STAT_CHECK_CONDITION || 1824 ncmd->status == SAM_STAT_COMMAND_TERMINATED) { 1825 dsprintk(NDEBUG_QUEUES, instance, "autosense: adding cmd %p to tail of autosense queue\n", 1826 cmd); 1827 list_add_tail(&ncmd->list, 1828 &hostdata->autosense); 1829 } else 1830 complete_cmd(instance, cmd); 1831 } 1832 1833 /* 1834 * Restore phase bits to 0 so an interrupted selection, 1835 * arbitration can resume. 1836 */ 1837 NCR5380_write(TARGET_COMMAND_REG, 0); 1838 1839 return; 1840 case MESSAGE_REJECT: 1841 /* Accept message by clearing ACK */ 1842 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 1843 switch (hostdata->last_message) { 1844 case HEAD_OF_QUEUE_TAG: 1845 case ORDERED_QUEUE_TAG: 1846 case SIMPLE_QUEUE_TAG: 1847 cmd->device->simple_tags = 0; 1848 hostdata->busy[cmd->device->id] |= (1 << (cmd->device->lun & 0xFF)); 1849 break; 1850 default: 1851 break; 1852 } 1853 break; 1854 case DISCONNECT: 1855 /* Accept message by clearing ACK */ 1856 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 1857 hostdata->connected = NULL; 1858 list_add(&ncmd->list, &hostdata->disconnected); 1859 dsprintk(NDEBUG_INFORMATION | NDEBUG_QUEUES, 1860 instance, "connected command %p for target %d lun %llu moved to disconnected queue\n", 1861 cmd, scmd_id(cmd), cmd->device->lun); 1862 1863 /* 1864 * Restore phase bits to 0 so an interrupted selection, 1865 * arbitration can resume. 1866 */ 1867 NCR5380_write(TARGET_COMMAND_REG, 0); 1868 1869#ifdef SUN3_SCSI_VME 1870 dregs->csr |= CSR_DMA_ENABLE; 1871#endif 1872 return; 1873 /* 1874 * The SCSI data pointer is *IMPLICITLY* saved on a disconnect 1875 * operation, in violation of the SCSI spec so we can safely 1876 * ignore SAVE/RESTORE pointers calls. 1877 * 1878 * Unfortunately, some disks violate the SCSI spec and 1879 * don't issue the required SAVE_POINTERS message before 1880 * disconnecting, and we have to break spec to remain 1881 * compatible. 1882 */ 1883 case SAVE_POINTERS: 1884 case RESTORE_POINTERS: 1885 /* Accept message by clearing ACK */ 1886 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 1887 break; 1888 case EXTENDED_MESSAGE: 1889 /* 1890 * Start the message buffer with the EXTENDED_MESSAGE 1891 * byte, since spi_print_msg() wants the whole thing. 1892 */ 1893 extended_msg[0] = EXTENDED_MESSAGE; 1894 /* Accept first byte by clearing ACK */ 1895 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 1896 1897 spin_unlock_irq(&hostdata->lock); 1898 1899 dsprintk(NDEBUG_EXTENDED, instance, "receiving extended message\n"); 1900 1901 len = 2; 1902 data = extended_msg + 1; 1903 phase = PHASE_MSGIN; 1904 NCR5380_transfer_pio(instance, &phase, &len, &data, 1); 1905 dsprintk(NDEBUG_EXTENDED, instance, "length %d, code 0x%02x\n", 1906 (int)extended_msg[1], 1907 (int)extended_msg[2]); 1908 1909 if (!len && extended_msg[1] > 0 && 1910 extended_msg[1] <= sizeof(extended_msg) - 2) { 1911 /* Accept third byte by clearing ACK */ 1912 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 1913 len = extended_msg[1] - 1; 1914 data = extended_msg + 3; 1915 phase = PHASE_MSGIN; 1916 1917 NCR5380_transfer_pio(instance, &phase, &len, &data, 1); 1918 dsprintk(NDEBUG_EXTENDED, instance, "message received, residual %d\n", 1919 len); 1920 1921 switch (extended_msg[2]) { 1922 case EXTENDED_SDTR: 1923 case EXTENDED_WDTR: 1924 tmp = 0; 1925 } 1926 } else if (len) { 1927 shost_printk(KERN_ERR, instance, "error receiving extended message\n"); 1928 tmp = 0; 1929 } else { 1930 shost_printk(KERN_NOTICE, instance, "extended message code %02x length %d is too long\n", 1931 extended_msg[2], extended_msg[1]); 1932 tmp = 0; 1933 } 1934 1935 spin_lock_irq(&hostdata->lock); 1936 if (!hostdata->connected) 1937 return; 1938 1939 /* Reject message */ 1940 fallthrough; 1941 default: 1942 /* 1943 * If we get something weird that we aren't expecting, 1944 * log it. 1945 */ 1946 if (tmp == EXTENDED_MESSAGE) 1947 scmd_printk(KERN_INFO, cmd, 1948 "rejecting unknown extended message code %02x, length %d\n", 1949 extended_msg[2], extended_msg[1]); 1950 else if (tmp) 1951 scmd_printk(KERN_INFO, cmd, 1952 "rejecting unknown message code %02x\n", 1953 tmp); 1954 1955 msgout = MESSAGE_REJECT; 1956 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN); 1957 break; 1958 } /* switch (tmp) */ 1959 break; 1960 case PHASE_MSGOUT: 1961 len = 1; 1962 data = &msgout; 1963 hostdata->last_message = msgout; 1964 NCR5380_transfer_pio(instance, &phase, &len, &data, 0); 1965 if (msgout == ABORT) { 1966 hostdata->connected = NULL; 1967 hostdata->busy[scmd_id(cmd)] &= ~(1 << cmd->device->lun); 1968 cmd->result = DID_ERROR << 16; 1969 complete_cmd(instance, cmd); 1970 return; 1971 } 1972 msgout = NOP; 1973 break; 1974 case PHASE_CMDOUT: 1975 len = cmd->cmd_len; 1976 data = cmd->cmnd; 1977 /* 1978 * XXX for performance reasons, on machines with a 1979 * PSEUDO-DMA architecture we should probably 1980 * use the dma transfer function. 1981 */ 1982 NCR5380_transfer_pio(instance, &phase, &len, &data, 0); 1983 break; 1984 case PHASE_STATIN: 1985 len = 1; 1986 tmp = ncmd->status; 1987 data = &tmp; 1988 NCR5380_transfer_pio(instance, &phase, &len, &data, 0); 1989 ncmd->status = tmp; 1990 break; 1991 default: 1992 shost_printk(KERN_ERR, instance, "unknown phase\n"); 1993 NCR5380_dprint(NDEBUG_ANY, instance); 1994 } /* switch(phase) */ 1995 } else { 1996 int err; 1997 1998 spin_unlock_irq(&hostdata->lock); 1999 err = NCR5380_poll_politely(hostdata, STATUS_REG, 2000 SR_REQ, SR_REQ, HZ); 2001 spin_lock_irq(&hostdata->lock); 2002 2003 if (err < 0 && hostdata->connected && 2004 !(NCR5380_read(STATUS_REG) & SR_BSY)) { 2005 scmd_printk(KERN_ERR, hostdata->connected, 2006 "BSY signal lost\n"); 2007 do_reset(instance); 2008 bus_reset_cleanup(instance); 2009 } 2010 } 2011 } 2012} 2013 2014/* 2015 * Function : void NCR5380_reselect (struct Scsi_Host *instance) 2016 * 2017 * Purpose : does reselection, initializing the instance->connected 2018 * field to point to the scsi_cmnd for which the I_T_L or I_T_L_Q 2019 * nexus has been reestablished, 2020 * 2021 * Inputs : instance - this instance of the NCR5380. 2022 */ 2023 2024static void NCR5380_reselect(struct Scsi_Host *instance) 2025{ 2026 struct NCR5380_hostdata *hostdata = shost_priv(instance); 2027 unsigned char target_mask; 2028 unsigned char lun; 2029 unsigned char msg[3]; 2030 struct NCR5380_cmd *ncmd; 2031 struct scsi_cmnd *tmp; 2032 2033 /* 2034 * Disable arbitration, etc. since the host adapter obviously 2035 * lost, and tell an interrupted NCR5380_select() to restart. 2036 */ 2037 2038 NCR5380_write(MODE_REG, MR_BASE); 2039 2040 target_mask = NCR5380_read(CURRENT_SCSI_DATA_REG) & ~(hostdata->id_mask); 2041 if (!target_mask || target_mask & (target_mask - 1)) { 2042 shost_printk(KERN_WARNING, instance, 2043 "reselect: bad target_mask 0x%02x\n", target_mask); 2044 return; 2045 } 2046 2047 /* 2048 * At this point, we have detected that our SCSI ID is on the bus, 2049 * SEL is true and BSY was false for at least one bus settle delay 2050 * (400 ns). 2051 * 2052 * We must assert BSY ourselves, until the target drops the SEL 2053 * signal. 2054 */ 2055 2056 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_BSY); 2057 if (NCR5380_poll_politely(hostdata, 2058 STATUS_REG, SR_SEL, 0, 0) < 0) { 2059 shost_printk(KERN_ERR, instance, "reselect: !SEL timeout\n"); 2060 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 2061 return; 2062 } 2063 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 2064 2065 /* 2066 * Wait for target to go into MSGIN. 2067 */ 2068 2069 if (NCR5380_poll_politely(hostdata, 2070 STATUS_REG, SR_REQ, SR_REQ, 0) < 0) { 2071 if ((NCR5380_read(STATUS_REG) & (SR_BSY | SR_SEL)) == 0) 2072 /* BUS FREE phase */ 2073 return; 2074 shost_printk(KERN_ERR, instance, "reselect: REQ timeout\n"); 2075 do_abort(instance, 0); 2076 return; 2077 } 2078 2079#ifdef CONFIG_SUN3 2080 /* acknowledge toggle to MSGIN */ 2081 NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(PHASE_MSGIN)); 2082 2083 /* peek at the byte without really hitting the bus */ 2084 msg[0] = NCR5380_read(CURRENT_SCSI_DATA_REG); 2085#else 2086 { 2087 int len = 1; 2088 unsigned char *data = msg; 2089 unsigned char phase = PHASE_MSGIN; 2090 2091 NCR5380_transfer_pio(instance, &phase, &len, &data, 0); 2092 2093 if (len) { 2094 do_abort(instance, 0); 2095 return; 2096 } 2097 } 2098#endif /* CONFIG_SUN3 */ 2099 2100 if (!(msg[0] & 0x80)) { 2101 shost_printk(KERN_ERR, instance, "expecting IDENTIFY message, got "); 2102 spi_print_msg(msg); 2103 printk("\n"); 2104 do_abort(instance, 0); 2105 return; 2106 } 2107 lun = msg[0] & 0x07; 2108 2109 /* 2110 * We need to add code for SCSI-II to track which devices have 2111 * I_T_L_Q nexuses established, and which have simple I_T_L 2112 * nexuses so we can chose to do additional data transfer. 2113 */ 2114 2115 /* 2116 * Find the command corresponding to the I_T_L or I_T_L_Q nexus we 2117 * just reestablished, and remove it from the disconnected queue. 2118 */ 2119 2120 tmp = NULL; 2121 list_for_each_entry(ncmd, &hostdata->disconnected, list) { 2122 struct scsi_cmnd *cmd = NCR5380_to_scmd(ncmd); 2123 2124 if (target_mask == (1 << scmd_id(cmd)) && 2125 lun == (u8)cmd->device->lun) { 2126 list_del(&ncmd->list); 2127 tmp = cmd; 2128 break; 2129 } 2130 } 2131 2132 if (tmp) { 2133 dsprintk(NDEBUG_RESELECTION | NDEBUG_QUEUES, instance, 2134 "reselect: removed %p from disconnected queue\n", tmp); 2135 } else { 2136 int target = ffs(target_mask) - 1; 2137 2138 shost_printk(KERN_ERR, instance, "target bitmask 0x%02x lun %d not in disconnected queue.\n", 2139 target_mask, lun); 2140 /* 2141 * Since we have an established nexus that we can't do anything 2142 * with, we must abort it. 2143 */ 2144 if (do_abort(instance, 0) == 0) 2145 hostdata->busy[target] &= ~(1 << lun); 2146 return; 2147 } 2148 2149#ifdef CONFIG_SUN3 2150 if (sun3_dma_setup_done != tmp) { 2151 int count; 2152 2153 advance_sg_buffer(ncmd); 2154 2155 count = sun3scsi_dma_xfer_len(hostdata, tmp); 2156 2157 if (count > 0) { 2158 if (tmp->sc_data_direction == DMA_TO_DEVICE) 2159 sun3scsi_dma_send_setup(hostdata, 2160 ncmd->ptr, count); 2161 else 2162 sun3scsi_dma_recv_setup(hostdata, 2163 ncmd->ptr, count); 2164 sun3_dma_setup_done = tmp; 2165 } 2166 } 2167 2168 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ACK); 2169#endif /* CONFIG_SUN3 */ 2170 2171 /* Accept message by clearing ACK */ 2172 NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE); 2173 2174 hostdata->connected = tmp; 2175 dsprintk(NDEBUG_RESELECTION, instance, "nexus established, target %d, lun %llu\n", 2176 scmd_id(tmp), tmp->device->lun); 2177} 2178 2179/** 2180 * list_find_cmd - test for presence of a command in a linked list 2181 * @haystack: list of commands 2182 * @needle: command to search for 2183 */ 2184 2185static bool list_find_cmd(struct list_head *haystack, 2186 struct scsi_cmnd *needle) 2187{ 2188 struct NCR5380_cmd *ncmd; 2189 2190 list_for_each_entry(ncmd, haystack, list) 2191 if (NCR5380_to_scmd(ncmd) == needle) 2192 return true; 2193 return false; 2194} 2195 2196/** 2197 * list_remove_cmd - remove a command from linked list 2198 * @haystack: list of commands 2199 * @needle: command to remove 2200 */ 2201 2202static bool list_del_cmd(struct list_head *haystack, 2203 struct scsi_cmnd *needle) 2204{ 2205 if (list_find_cmd(haystack, needle)) { 2206 struct NCR5380_cmd *ncmd = NCR5380_to_ncmd(needle); 2207 2208 list_del(&ncmd->list); 2209 return true; 2210 } 2211 return false; 2212} 2213 2214/** 2215 * NCR5380_abort - scsi host eh_abort_handler() method 2216 * @cmd: the command to be aborted 2217 * 2218 * Try to abort a given command by removing it from queues and/or sending 2219 * the target an abort message. This may not succeed in causing a target 2220 * to abort the command. Nonetheless, the low-level driver must forget about 2221 * the command because the mid-layer reclaims it and it may be re-issued. 2222 * 2223 * The normal path taken by a command is as follows. For EH we trace this 2224 * same path to locate and abort the command. 2225 * 2226 * unissued -> selecting -> [unissued -> selecting ->]... connected -> 2227 * [disconnected -> connected ->]... 2228 * [autosense -> connected ->] done 2229 * 2230 * If cmd was not found at all then presumably it has already been completed, 2231 * in which case return SUCCESS to try to avoid further EH measures. 2232 * 2233 * If the command has not completed yet, we must not fail to find it. 2234 * We have no option but to forget the aborted command (even if it still 2235 * lacks sense data). The mid-layer may re-issue a command that is in error 2236 * recovery (see scsi_send_eh_cmnd), but the logic and data structures in 2237 * this driver are such that a command can appear on one queue only. 2238 * 2239 * The lock protects driver data structures, but EH handlers also use it 2240 * to serialize their own execution and prevent their own re-entry. 2241 */ 2242 2243static int NCR5380_abort(struct scsi_cmnd *cmd) 2244{ 2245 struct Scsi_Host *instance = cmd->device->host; 2246 struct NCR5380_hostdata *hostdata = shost_priv(instance); 2247 unsigned long flags; 2248 int result = SUCCESS; 2249 2250 spin_lock_irqsave(&hostdata->lock, flags); 2251 2252#if (NDEBUG & NDEBUG_ANY) 2253 scmd_printk(KERN_INFO, cmd, __func__); 2254#endif 2255 NCR5380_dprint(NDEBUG_ANY, instance); 2256 NCR5380_dprint_phase(NDEBUG_ANY, instance); 2257 2258 if (list_del_cmd(&hostdata->unissued, cmd)) { 2259 dsprintk(NDEBUG_ABORT, instance, 2260 "abort: removed %p from issue queue\n", cmd); 2261 cmd->result = DID_ABORT << 16; 2262 scsi_done(cmd); /* No tag or busy flag to worry about */ 2263 goto out; 2264 } 2265 2266 if (hostdata->selecting == cmd) { 2267 dsprintk(NDEBUG_ABORT, instance, 2268 "abort: cmd %p == selecting\n", cmd); 2269 hostdata->selecting = NULL; 2270 cmd->result = DID_ABORT << 16; 2271 complete_cmd(instance, cmd); 2272 goto out; 2273 } 2274 2275 if (list_del_cmd(&hostdata->disconnected, cmd)) { 2276 dsprintk(NDEBUG_ABORT, instance, 2277 "abort: removed %p from disconnected list\n", cmd); 2278 /* Can't call NCR5380_select() and send ABORT because that 2279 * means releasing the lock. Need a bus reset. 2280 */ 2281 set_host_byte(cmd, DID_ERROR); 2282 complete_cmd(instance, cmd); 2283 result = FAILED; 2284 goto out; 2285 } 2286 2287 if (hostdata->connected == cmd) { 2288 dsprintk(NDEBUG_ABORT, instance, "abort: cmd %p is connected\n", cmd); 2289 hostdata->connected = NULL; 2290 hostdata->dma_len = 0; 2291 if (do_abort(instance, 0) < 0) { 2292 set_host_byte(cmd, DID_ERROR); 2293 complete_cmd(instance, cmd); 2294 result = FAILED; 2295 goto out; 2296 } 2297 set_host_byte(cmd, DID_ABORT); 2298 complete_cmd(instance, cmd); 2299 goto out; 2300 } 2301 2302 if (list_del_cmd(&hostdata->autosense, cmd)) { 2303 dsprintk(NDEBUG_ABORT, instance, 2304 "abort: removed %p from sense queue\n", cmd); 2305 complete_cmd(instance, cmd); 2306 } 2307 2308out: 2309 if (result == FAILED) 2310 dsprintk(NDEBUG_ABORT, instance, "abort: failed to abort %p\n", cmd); 2311 else { 2312 hostdata->busy[scmd_id(cmd)] &= ~(1 << cmd->device->lun); 2313 dsprintk(NDEBUG_ABORT, instance, "abort: successfully aborted %p\n", cmd); 2314 } 2315 2316 queue_work(hostdata->work_q, &hostdata->main_task); 2317 spin_unlock_irqrestore(&hostdata->lock, flags); 2318 2319 return result; 2320} 2321 2322 2323static void bus_reset_cleanup(struct Scsi_Host *instance) 2324{ 2325 struct NCR5380_hostdata *hostdata = shost_priv(instance); 2326 int i; 2327 struct NCR5380_cmd *ncmd; 2328 2329 /* reset NCR registers */ 2330 NCR5380_write(MODE_REG, MR_BASE); 2331 NCR5380_write(TARGET_COMMAND_REG, 0); 2332 NCR5380_write(SELECT_ENABLE_REG, 0); 2333 2334 /* After the reset, there are no more connected or disconnected commands 2335 * and no busy units; so clear the low-level status here to avoid 2336 * conflicts when the mid-level code tries to wake up the affected 2337 * commands! 2338 */ 2339 2340 if (hostdata->selecting) { 2341 hostdata->selecting->result = DID_RESET << 16; 2342 complete_cmd(instance, hostdata->selecting); 2343 hostdata->selecting = NULL; 2344 } 2345 2346 list_for_each_entry(ncmd, &hostdata->disconnected, list) { 2347 struct scsi_cmnd *cmd = NCR5380_to_scmd(ncmd); 2348 2349 set_host_byte(cmd, DID_RESET); 2350 complete_cmd(instance, cmd); 2351 } 2352 INIT_LIST_HEAD(&hostdata->disconnected); 2353 2354 list_for_each_entry(ncmd, &hostdata->autosense, list) { 2355 struct scsi_cmnd *cmd = NCR5380_to_scmd(ncmd); 2356 2357 scsi_done(cmd); 2358 } 2359 INIT_LIST_HEAD(&hostdata->autosense); 2360 2361 if (hostdata->connected) { 2362 set_host_byte(hostdata->connected, DID_RESET); 2363 complete_cmd(instance, hostdata->connected); 2364 hostdata->connected = NULL; 2365 } 2366 2367 for (i = 0; i < 8; ++i) 2368 hostdata->busy[i] = 0; 2369 hostdata->dma_len = 0; 2370 2371 queue_work(hostdata->work_q, &hostdata->main_task); 2372} 2373 2374/** 2375 * NCR5380_host_reset - reset the SCSI host 2376 * @cmd: SCSI command undergoing EH 2377 * 2378 * Returns SUCCESS 2379 */ 2380 2381static int NCR5380_host_reset(struct scsi_cmnd *cmd) 2382{ 2383 struct Scsi_Host *instance = cmd->device->host; 2384 struct NCR5380_hostdata *hostdata = shost_priv(instance); 2385 unsigned long flags; 2386 struct NCR5380_cmd *ncmd; 2387 2388 spin_lock_irqsave(&hostdata->lock, flags); 2389 2390#if (NDEBUG & NDEBUG_ANY) 2391 shost_printk(KERN_INFO, instance, __func__); 2392#endif 2393 NCR5380_dprint(NDEBUG_ANY, instance); 2394 NCR5380_dprint_phase(NDEBUG_ANY, instance); 2395 2396 list_for_each_entry(ncmd, &hostdata->unissued, list) { 2397 struct scsi_cmnd *scmd = NCR5380_to_scmd(ncmd); 2398 2399 scmd->result = DID_RESET << 16; 2400 scsi_done(scmd); 2401 } 2402 INIT_LIST_HEAD(&hostdata->unissued); 2403 2404 do_reset(instance); 2405 bus_reset_cleanup(instance); 2406 2407 spin_unlock_irqrestore(&hostdata->lock, flags); 2408 2409 return SUCCESS; 2410}
~/
Read-only file preview.