File Index
Files and directories
Sign in
FILE

iwl-op-mode.h

File preview with syntax highlighting.

linux-6.19.14/drivers/net/wireless/intel/iwlwifi/iwl-op-mode.h C
  1/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
  2/*
  3 * Copyright (C) 2005-2014, 2018-2021, 2024-2025 Intel Corporation
  4 * Copyright (C) 2013-2014 Intel Mobile Communications GmbH
  5 * Copyright (C) 2015 Intel Deutschland GmbH
  6 */
  7#ifndef __iwl_op_mode_h__
  8#define __iwl_op_mode_h__
  9
 10#include <linux/netdevice.h>
 11#include <linux/debugfs.h>
 12#include "iwl-dbg-tlv.h"
 13
 14struct iwl_op_mode;
 15struct iwl_trans;
 16struct sk_buff;
 17struct iwl_device_cmd;
 18struct iwl_rx_cmd_buffer;
 19struct iwl_fw;
 20struct iwl_rf_cfg;
 21
 22/**
 23 * DOC: Operational mode - what is it ?
 24 *
 25 * The operational mode (a.k.a. op_mode) is the layer that implements
 26 * mac80211's handlers. It knows two APIs: mac80211's and the fw's. It uses
 27 * the transport API to access the HW. The op_mode doesn't need to know how the
 28 * underlying HW works, since the transport layer takes care of that.
 29 *
 30 * There can be several op_mode: i.e. different fw APIs will require two
 31 * different op_modes. This is why the op_mode is virtualized.
 32 */
 33
 34/**
 35 * DOC: Life cycle of the Operational mode
 36 *
 37 * The operational mode has a very simple life cycle.
 38 *
 39 *	1) The driver layer (iwl-drv.c) chooses the op_mode based on the
 40 *	   capabilities advertised by the fw file (in TLV format).
 41 *	2) The driver layer starts the op_mode (ops->start)
 42 *	3) The op_mode registers mac80211
 43 *	4) The op_mode is governed by mac80211
 44 *	5) The driver layer stops the op_mode
 45 */
 46
 47/**
 48 * enum iwl_fw_error_type - FW error types/sources
 49 * @IWL_ERR_TYPE_IRQ: "normal" FW error through an IRQ
 50 * @IWL_ERR_TYPE_NMI_FORCED: NMI was forced by driver
 51 * @IWL_ERR_TYPE_RESET_HS_TIMEOUT: reset handshake timed out,
 52 *	any debug collection must happen synchronously as
 53 *	the device will be shut down
 54 * @IWL_ERR_TYPE_CMD_QUEUE_FULL: command queue was full
 55 * @IWL_ERR_TYPE_TOP_RESET_BY_BT: TOP reset initiated by BT
 56 * @IWL_ERR_TYPE_TOP_FATAL_ERROR: TOP fatal error
 57 * @IWL_ERR_TYPE_TOP_RESET_FAILED: TOP reset failed
 58 * @IWL_ERR_TYPE_DEBUGFS: error/reset indication from debugfs
 59 */
 60enum iwl_fw_error_type {
 61	IWL_ERR_TYPE_IRQ,
 62	IWL_ERR_TYPE_NMI_FORCED,
 63	IWL_ERR_TYPE_RESET_HS_TIMEOUT,
 64	IWL_ERR_TYPE_CMD_QUEUE_FULL,
 65	IWL_ERR_TYPE_TOP_RESET_BY_BT,
 66	IWL_ERR_TYPE_TOP_FATAL_ERROR,
 67	IWL_ERR_TYPE_TOP_RESET_FAILED,
 68	IWL_ERR_TYPE_DEBUGFS,
 69};
 70
 71/**
 72 * enum iwl_fw_error_context - error dump context
 73 * @IWL_ERR_CONTEXT_WORKER: regular from worker context,
 74 *	opmode must acquire locks and must also check
 75 *	for @IWL_ERR_CONTEXT_ABORT after acquiring locks
 76 * @IWL_ERR_CONTEXT_FROM_OPMODE: context is in a call
 77 *	originating from the opmode, e.g. while resetting
 78 *	or stopping the device, so opmode must not acquire
 79 *	any locks
 80 * @IWL_ERR_CONTEXT_ABORT: after lock acquisition, indicates
 81 *	that the dump already happened via another callback
 82 *	(currently only while stopping the device) via the
 83 *	@IWL_ERR_CONTEXT_FROM_OPMODE context, and this call
 84 *	must be aborted
 85 */
 86enum iwl_fw_error_context {
 87	IWL_ERR_CONTEXT_WORKER,
 88	IWL_ERR_CONTEXT_FROM_OPMODE,
 89	IWL_ERR_CONTEXT_ABORT,
 90};
 91
 92/**
 93 * struct iwl_fw_error_dump_mode - error dump mode for callback
 94 * @type: The reason for the dump, per &enum iwl_fw_error_type.
 95 * @context: The context for the dump, may also indicate this
 96 *	call needs to be skipped. This MUST be checked before
 97 *	and after acquiring any locks in the op-mode!
 98 */
 99struct iwl_fw_error_dump_mode {
100	enum iwl_fw_error_type type;
101	enum iwl_fw_error_context context;
102};
103
104/**
105 * struct iwl_op_mode_ops - op_mode specific operations
106 *
107 * The op_mode exports its ops so that external components can start it and
108 * interact with it. The driver layer typically calls the start and stop
109 * handlers, the transport layer calls the others.
110 *
111 * All the handlers MUST be implemented, except @rx_rss which can be left
112 * out *iff* the opmode will never run on hardware with multi-queue capability.
113 *
114 * @start: start the op_mode. The transport layer is already allocated.
115 *	May sleep
116 * @stop: stop the op_mode. Must free all the memory allocated.
117 *	May sleep
118 * @rx: Rx notification to the op_mode. rxb is the Rx buffer itself. Cmd is the
119 *	HCMD this Rx responds to. Can't sleep.
120 * @rx_rss: data queue RX notification to the op_mode, for (data) notifications
121 *	received on the RSS queue(s). The queue parameter indicates which of the
122 *	RSS queues received this frame; it will always be non-zero.
123 *	This method must not sleep.
124 * @queue_full: notifies that a HW queue is full.
125 *	Must be atomic and called with BH disabled.
126 * @queue_not_full: notifies that a HW queue is not full any more.
127 *	Must be atomic and called with BH disabled.
128 * @hw_rf_kill: notifies of a change in the HW rf kill switch. True means that
129 *	the radio is killed. Return %true if the device should be stopped by
130 *	the transport immediately after the call. May sleep.
131 *	Note that this must not return %true for newer devices using gen2 PCIe
132 *	transport.
133 * @free_skb: allows the transport layer to free skbs that haven't been
134 *	reclaimed by the op_mode. This can happen when the driver is freed and
135 *	there are Tx packets pending in the transport layer.
136 *	Must be atomic
137 * @nic_error: error notification. Must be atomic, the op mode should handle
138 *	the error (e.g. abort notification waiters) and print the error if
139 *	applicable
140 * @dump_error: NIC error dump collection (can sleep, synchronous)
141 * @sw_reset: (maybe) initiate a software reset, return %true if started
142 * @nic_config: configure NIC, called before firmware is started.
143 *	May sleep
144 * @wimax_active: invoked when WiMax becomes active. May sleep
145 * @time_point: called when transport layer wants to collect debug data
146 * @device_powered_off: called upon resume from hibernation but not only.
147 *	Op_mode needs to reset its internal state because the device did not
148 *	survive the system state transition. The firmware is no longer running,
149 *	etc...
150 * @dump: Op_mode needs to collect the firmware dump upon this handler
151 *	being called.
152 */
153struct iwl_op_mode_ops {
154	struct iwl_op_mode *(*start)(struct iwl_trans *trans,
155				     const struct iwl_rf_cfg *cfg,
156				     const struct iwl_fw *fw,
157				     struct dentry *dbgfs_dir);
158	void (*stop)(struct iwl_op_mode *op_mode);
159	void (*rx)(struct iwl_op_mode *op_mode, struct napi_struct *napi,
160		   struct iwl_rx_cmd_buffer *rxb);
161	void (*rx_rss)(struct iwl_op_mode *op_mode, struct napi_struct *napi,
162		       struct iwl_rx_cmd_buffer *rxb, unsigned int queue);
163	void (*queue_full)(struct iwl_op_mode *op_mode, int queue);
164	void (*queue_not_full)(struct iwl_op_mode *op_mode, int queue);
165	bool (*hw_rf_kill)(struct iwl_op_mode *op_mode, bool state);
166	void (*free_skb)(struct iwl_op_mode *op_mode, struct sk_buff *skb);
167	void (*nic_error)(struct iwl_op_mode *op_mode,
168			  enum iwl_fw_error_type type);
169	void (*dump_error)(struct iwl_op_mode *op_mode,
170			   struct iwl_fw_error_dump_mode *mode);
171	bool (*sw_reset)(struct iwl_op_mode *op_mode,
172			 enum iwl_fw_error_type type);
173	void (*nic_config)(struct iwl_op_mode *op_mode);
174	void (*wimax_active)(struct iwl_op_mode *op_mode);
175	void (*time_point)(struct iwl_op_mode *op_mode,
176			   enum iwl_fw_ini_time_point tp_id,
177			   union iwl_dbg_tlv_tp_data *tp_data);
178	void (*device_powered_off)(struct iwl_op_mode *op_mode);
179	void (*dump)(struct iwl_op_mode *op_mode);
180};
181
182int iwl_opmode_register(const char *name, const struct iwl_op_mode_ops *ops);
183void iwl_opmode_deregister(const char *name);
184
185/**
186 * struct iwl_op_mode - operational mode
187 * @ops: pointer to its own ops
188 * @op_mode_specific: per-opmode data
189 *
190 * This holds an implementation of the mac80211 / fw API.
191 */
192struct iwl_op_mode {
193	const struct iwl_op_mode_ops *ops;
194
195	char op_mode_specific[] __aligned(sizeof(void *));
196};
197
198static inline void iwl_op_mode_stop(struct iwl_op_mode *op_mode)
199{
200	might_sleep();
201	op_mode->ops->stop(op_mode);
202}
203
204static inline void iwl_op_mode_rx(struct iwl_op_mode *op_mode,
205				  struct napi_struct *napi,
206				  struct iwl_rx_cmd_buffer *rxb)
207{
208	return op_mode->ops->rx(op_mode, napi, rxb);
209}
210
211static inline void iwl_op_mode_rx_rss(struct iwl_op_mode *op_mode,
212				      struct napi_struct *napi,
213				      struct iwl_rx_cmd_buffer *rxb,
214				      unsigned int queue)
215{
216	op_mode->ops->rx_rss(op_mode, napi, rxb, queue);
217}
218
219static inline void iwl_op_mode_queue_full(struct iwl_op_mode *op_mode,
220					  int queue)
221{
222	op_mode->ops->queue_full(op_mode, queue);
223}
224
225static inline void iwl_op_mode_queue_not_full(struct iwl_op_mode *op_mode,
226					      int queue)
227{
228	op_mode->ops->queue_not_full(op_mode, queue);
229}
230
231static inline bool __must_check
232iwl_op_mode_hw_rf_kill(struct iwl_op_mode *op_mode, bool state)
233{
234	might_sleep();
235	return op_mode->ops->hw_rf_kill(op_mode, state);
236}
237
238static inline void iwl_op_mode_free_skb(struct iwl_op_mode *op_mode,
239					struct sk_buff *skb)
240{
241	if (WARN_ON_ONCE(!op_mode))
242		return;
243	op_mode->ops->free_skb(op_mode, skb);
244}
245
246static inline void iwl_op_mode_nic_error(struct iwl_op_mode *op_mode,
247					 enum iwl_fw_error_type type)
248{
249	op_mode->ops->nic_error(op_mode, type);
250}
251
252static inline void iwl_op_mode_dump_error(struct iwl_op_mode *op_mode,
253					  struct iwl_fw_error_dump_mode *mode)
254{
255	might_sleep();
256
257	if (WARN_ON(mode->type == IWL_ERR_TYPE_TOP_RESET_BY_BT))
258		return;
259
260	if (op_mode->ops->dump_error)
261		op_mode->ops->dump_error(op_mode, mode);
262}
263
264static inline void iwl_op_mode_nic_config(struct iwl_op_mode *op_mode)
265{
266	might_sleep();
267	if (op_mode->ops->nic_config)
268		op_mode->ops->nic_config(op_mode);
269}
270
271static inline void iwl_op_mode_wimax_active(struct iwl_op_mode *op_mode)
272{
273	might_sleep();
274	op_mode->ops->wimax_active(op_mode);
275}
276
277static inline void iwl_op_mode_time_point(struct iwl_op_mode *op_mode,
278					  enum iwl_fw_ini_time_point tp_id,
279					  union iwl_dbg_tlv_tp_data *tp_data)
280{
281	if (!op_mode || !op_mode->ops || !op_mode->ops->time_point)
282		return;
283	op_mode->ops->time_point(op_mode, tp_id, tp_data);
284}
285
286static inline void iwl_op_mode_device_powered_off(struct iwl_op_mode *op_mode)
287{
288	if (!op_mode || !op_mode->ops || !op_mode->ops->device_powered_off)
289		return;
290	op_mode->ops->device_powered_off(op_mode);
291}
292
293static inline void iwl_op_mode_dump(struct iwl_op_mode *op_mode)
294{
295	if (!op_mode || !op_mode->ops || !op_mode->ops->dump)
296		return;
297	op_mode->ops->dump(op_mode);
298}
299
300#endif /* __iwl_op_mode_h__ */
~/ Read-only file preview.