Kconfig

  1# SPDX-License-Identifier: GPL-2.0-only
  2#
  3# HISILICON device configuration
  4#
  5
  6config NET_VENDOR_HISILICON
  7	bool "Hisilicon devices"
  8	default y
  9	depends on OF || ACPI
 10	help
 11	  If you have a network (Ethernet) card belonging to this class, say Y.
 12
 13	  Note that the answer to this question doesn't directly affect the
 14	  kernel: saying N will just cause the configurator to skip all
 15	  the questions about Hisilicon devices. If you say Y, you will be asked
 16	  for your specific card in the following questions.
 17
 18if NET_VENDOR_HISILICON
 19
 20if ARM || ARM64 || COMPILE_TEST
 21
 22config HIX5HD2_GMAC
 23	tristate "Hisilicon HIX5HD2 Family Network Device Support"
 24	select PHYLIB
 25	help
 26	  This selects the hix5hd2 mac family network device.
 27
 28config HISI_FEMAC
 29	tristate "Hisilicon Fast Ethernet MAC device support"
 30	depends on HAS_IOMEM
 31	select PHYLIB
 32	select RESET_CONTROLLER
 33	help
 34	  This selects the Hisilicon Fast Ethernet MAC device(FEMAC).
 35	  The FEMAC receives and transmits data over Ethernet
 36	  ports at 10/100 Mbps in full-duplex or half-duplex mode.
 37	  The FEMAC exchanges data with the CPU, and supports
 38	  the energy efficient Ethernet (EEE).
 39
 40config HIP04_ETH
 41	tristate "HISILICON P04 Ethernet support"
 42	depends on HAS_IOMEM	# For MFD_SYSCON
 43	select MARVELL_PHY
 44	select MFD_SYSCON
 45	select HNS_MDIO
 46	help
 47	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
 48	  want to use the internal ethernet then you should answer Y to this.
 49
 50config HI13X1_GMAC
 51	bool "Hisilicon HI13X1 Network Device Support"
 52	depends on HIP04_ETH
 53	help
 54	  If you wish to compile a kernel for a hardware with hisilicon hi13x1_gamc
 55	  then you should answer Y to this. This makes this driver suitable for use
 56	  on certain boards such as the HI13X1.
 57
 58	  If you are unsure, say N.
 59
 60config HNS_MDIO
 61	tristate
 62	select PHYLIB
 63	help
 64	  This selects the HNS MDIO support. It is needed by HNS_DSAF to access
 65	  the PHY
 66
 67config HNS
 68	tristate
 69	help
 70	  This selects the framework support for Hisilicon Network Subsystem. It
 71	  is needed by any driver which provides HNS acceleration engine or make
 72	  use of the engine
 73
 74config HNS_DSAF
 75	tristate "Hisilicon HNS DSAF device Support"
 76	select HNS
 77	select HNS_MDIO
 78	help
 79	  This selects the DSAF (Distributed System Area Frabric) network
 80	  acceleration engine support. The engine is used in Hisilicon hip05,
 81	  Hi1610 and further ICT SoC
 82
 83config HNS_ENET
 84	tristate "Hisilicon HNS Ethernet Device Support"
 85	select PHYLIB
 86	select HNS
 87	help
 88	  This selects the general ethernet driver for HNS.  This module make
 89	  use of any HNS AE driver, such as HNS_DSAF
 90
 91config HNS3
 92	tristate "Hisilicon Network Subsystem Support HNS3 (Framework)"
 93	depends on PCI
 94	select NET_DEVLINK
 95	select PAGE_POOL
 96	help
 97	  This selects the framework support for Hisilicon Network Subsystem 3.
 98	  This layer facilitates clients like ENET, RoCE and user-space ethernet
 99	  drivers(like ODP)to register with HNAE devices and their associated
100	  operations.
101
102if HNS3
103
104config HNS3_HCLGE
105	tristate "Hisilicon HNS3 HCLGE Acceleration Engine & Compatibility Layer Support"
106	default m
107	depends on PCI_MSI
108	depends on PTP_1588_CLOCK_OPTIONAL
109	help
110	  This selects the HNS3_HCLGE network acceleration engine & its hardware
111	  compatibility layer. The engine would be used in Hisilicon hip08 family of
112	  SoCs and further upcoming SoCs.
113
114config HNS3_DCB
115	bool "Hisilicon HNS3 Data Center Bridge Support"
116	default n
117	depends on HNS3_HCLGE && DCB
118	help
119	  Say Y here if you want to use Data Center Bridging (DCB) in the HNS3 driver.
120
121	  If unsure, say N.
122
123config HNS3_HCLGEVF
124	tristate "Hisilicon HNS3VF Acceleration Engine & Compatibility Layer Support"
125	depends on PCI_MSI
126	depends on HNS3_HCLGE
127	help
128	  This selects the HNS3 VF drivers network acceleration engine & its hardware
129	  compatibility layer. The engine would be used in Hisilicon hip08 family of
130	  SoCs and further upcoming SoCs.
131
132config HNS3_ENET
133	tristate "Hisilicon HNS3 Ethernet Device Support"
134	default m
135	depends on 64BIT && PCI
136	depends on INET
137	select DIMLIB
138	help
139	  This selects the Ethernet Driver for Hisilicon Network Subsystem 3 for hip08
140	  family of SoCs. This module depends upon HNAE3 driver to access the HNAE3
141	  devices and their associated operations.
142
143endif #HNS3
144
145endif # ARM || ARM64 || COMPILE_TEST
146
147config HIBMCGE
148	tristate "Hisilicon BMC Gigabit Ethernet Device Support"
149	depends on PCI && PCI_MSI
150	select PHYLIB
151	select FIXED_PHY
152	select MOTORCOMM_PHY
153	select REALTEK_PHY
154	select PAGE_POOL
155	help
156	  If you wish to compile a kernel for a BMC with HIBMC-xx_gmac
157	  then you should answer Y to this. This makes this driver suitable for use
158	  on certain boards such as the HIBMC-210.
159
160	  If you are unsure, say N.
161
162endif # NET_VENDOR_HISILICON