Kconfig

  1# SPDX-License-Identifier: GPL-2.0-only
  2#
  3# Freescale device configuration
  4#
  5
  6config NET_VENDOR_FREESCALE
  7	bool "Freescale devices"
  8	default y
  9	depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
 10		   M523x || M527x || M5272 || M528x || M520x || M532x || \
 11		   ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) || \
 12		   ARCH_LAYERSCAPE || ARCH_S32 || COMPILE_TEST
 13	help
 14	  If you have a network (Ethernet) card belonging to this class, say Y.
 15
 16	  Note that the answer to this question doesn't directly affect the
 17	  kernel: saying N will just cause the configurator to skip all
 18	  the questions about Freescale devices. If you say Y, you will be
 19	  asked for your specific card in the following questions.
 20
 21if NET_VENDOR_FREESCALE
 22
 23config FEC
 24	tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
 25	depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
 26		   ARCH_MXC || ARCH_S32 || SOC_IMX28 || COMPILE_TEST)
 27	default ARCH_MXC || SOC_IMX28 if ARM
 28	depends on PTP_1588_CLOCK_OPTIONAL
 29	select CRC32
 30	select PHYLIB
 31	select FIXED_PHY
 32	select PAGE_POOL
 33	imply PAGE_POOL_STATS
 34	imply NET_SELFTESTS
 35	help
 36	  Say Y here if you want to use the built-in 10/100 Fast ethernet
 37	  controller on some Motorola ColdFire and Freescale i.MX/S32 processors.
 38
 39config FEC_MPC52xx
 40	tristate "FEC MPC52xx driver"
 41	depends on PPC_MPC52xx && PPC_BESTCOMM
 42	select CRC32
 43	select PHYLIB
 44	select PPC_BESTCOMM_FEC
 45	help
 46	  This option enables support for the MPC5200's on-chip
 47	  Fast Ethernet Controller
 48	  If compiled as module, it will be called fec_mpc52xx.
 49
 50config FEC_MPC52xx_MDIO
 51	bool "FEC MPC52xx MDIO bus driver"
 52	depends on FEC_MPC52xx
 53	default y
 54	help
 55	  The MPC5200's FEC can connect to the Ethernet either with
 56	  an external MII PHY chip or 10 Mbps 7-wire interface
 57	  (Motorola? industry standard).
 58	  If your board uses an external PHY connected to FEC, enable this.
 59	  If not sure, enable.
 60	  If compiled as module, it will be called fec_mpc52xx_phy.
 61
 62source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
 63source "drivers/net/ethernet/freescale/fman/Kconfig"
 64
 65config FSL_PQ_MDIO
 66	tristate "Freescale PQ MDIO"
 67	select PHYLIB
 68	help
 69	  This driver supports the MDIO bus used by the gianfar and UCC drivers.
 70
 71config FSL_XGMAC_MDIO
 72	tristate "Freescale XGMAC MDIO"
 73	select PHYLIB
 74	depends on OF
 75	select OF_MDIO
 76	help
 77	  This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and
 78	  on the FMan mEMAC (which supports both Clauses 22 and 45)
 79
 80config UCC_GETH
 81	tristate "Freescale QE Gigabit Ethernet"
 82	depends on QUICC_ENGINE && PPC32
 83	select FSL_PQ_MDIO
 84	select PHYLINK
 85	help
 86	  This driver supports the Gigabit Ethernet mode of the QUICC Engine,
 87	  which is available on some Freescale SOCs.
 88
 89config UGETH_TX_ON_DEMAND
 90	bool "Transmit on Demand support"
 91	depends on UCC_GETH
 92
 93config GIANFAR
 94	tristate "Gianfar Ethernet"
 95	depends on HAS_DMA
 96	select FSL_PQ_MDIO
 97	select PHYLIB
 98	select FIXED_PHY
 99	select CRC32
100	help
101	  This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
102	  and MPC86xx family of chips, the eTSEC on LS1021A and the FEC
103	  on the 8540.
104
105source "drivers/net/ethernet/freescale/dpaa/Kconfig"
106source "drivers/net/ethernet/freescale/dpaa2/Kconfig"
107source "drivers/net/ethernet/freescale/enetc/Kconfig"
108
109endif # NET_VENDOR_FREESCALE