gef_sbc610.c

  1// SPDX-License-Identifier: GPL-2.0-or-later
  2/*
  3 * GE SBC610 board support
  4 *
  5 * Author: Martyn Welch <martyn.welch@ge.com>
  6 *
  7 * Copyright 2008 GE Intelligent Platforms Embedded Systems, Inc.
  8 *
  9 * Based on: mpc86xx_hpcn.c (MPC86xx HPCN board specific routines)
 10 * Copyright 2006 Freescale Semiconductor Inc.
 11 *
 12 * NEC fixup adapted from arch/mips/pci/fixup-lm2e.c
 13 */
 14
 15#include <linux/stddef.h>
 16#include <linux/kernel.h>
 17#include <linux/pci.h>
 18#include <linux/kdev_t.h>
 19#include <linux/delay.h>
 20#include <linux/seq_file.h>
 21#include <linux/of.h>
 22#include <linux/of_address.h>
 23
 24#include <asm/time.h>
 25#include <asm/machdep.h>
 26#include <asm/pci-bridge.h>
 27#include <mm/mmu_decl.h>
 28#include <asm/udbg.h>
 29
 30#include <asm/mpic.h>
 31#include <asm/nvram.h>
 32
 33#include <sysdev/fsl_pci.h>
 34#include <sysdev/fsl_soc.h>
 35#include <sysdev/ge/ge_pic.h>
 36
 37#include "mpc86xx.h"
 38
 39#undef DEBUG
 40
 41#ifdef DEBUG
 42#define DBG (fmt...) do { printk(KERN_ERR "SBC610: " fmt); } while (0)
 43#else
 44#define DBG (fmt...) do { } while (0)
 45#endif
 46
 47void __iomem *sbc610_regs;
 48
 49static void __init gef_sbc610_init_irq(void)
 50{
 51	struct device_node *cascade_node = NULL;
 52
 53	mpc86xx_init_irq();
 54
 55	/*
 56	 * There is a simple interrupt handler in the main FPGA, this needs
 57	 * to be cascaded into the MPIC
 58	 */
 59	cascade_node = of_find_compatible_node(NULL, NULL, "gef,fpga-pic");
 60	if (!cascade_node) {
 61		printk(KERN_WARNING "SBC610: No FPGA PIC\n");
 62		return;
 63	}
 64
 65	gef_pic_init(cascade_node);
 66	of_node_put(cascade_node);
 67}
 68
 69static void __init gef_sbc610_setup_arch(void)
 70{
 71	struct device_node *regs;
 72
 73	printk(KERN_INFO "GE Intelligent Platforms SBC610 6U VPX SBC\n");
 74
 75#ifdef CONFIG_SMP
 76	mpc86xx_smp_init();
 77#endif
 78
 79	fsl_pci_assign_primary();
 80
 81	/* Remap basic board registers */
 82	regs = of_find_compatible_node(NULL, NULL, "gef,fpga-regs");
 83	if (regs) {
 84		sbc610_regs = of_iomap(regs, 0);
 85		if (sbc610_regs == NULL)
 86			printk(KERN_WARNING "Unable to map board registers\n");
 87		of_node_put(regs);
 88	}
 89
 90#if defined(CONFIG_MMIO_NVRAM)
 91	mmio_nvram_init();
 92#endif
 93}
 94
 95/* Return the PCB revision */
 96static unsigned int gef_sbc610_get_pcb_rev(void)
 97{
 98	unsigned int reg;
 99
100	reg = ioread32(sbc610_regs);
101	return (reg >> 8) & 0xff;
102}
103
104/* Return the board (software) revision */
105static unsigned int gef_sbc610_get_board_rev(void)
106{
107	unsigned int reg;
108
109	reg = ioread32(sbc610_regs);
110	return (reg >> 16) & 0xff;
111}
112
113/* Return the FPGA revision */
114static unsigned int gef_sbc610_get_fpga_rev(void)
115{
116	unsigned int reg;
117
118	reg = ioread32(sbc610_regs);
119	return (reg >> 24) & 0xf;
120}
121
122static void gef_sbc610_show_cpuinfo(struct seq_file *m)
123{
124	uint svid = mfspr(SPRN_SVR);
125
126	seq_printf(m, "Vendor\t\t: GE Intelligent Platforms\n");
127
128	seq_printf(m, "Revision\t: %u%c\n", gef_sbc610_get_pcb_rev(),
129		('A' + gef_sbc610_get_board_rev() - 1));
130	seq_printf(m, "FPGA Revision\t: %u\n", gef_sbc610_get_fpga_rev());
131
132	seq_printf(m, "SVR\t\t: 0x%x\n", svid);
133}
134
135static void gef_sbc610_nec_fixup(struct pci_dev *pdev)
136{
137	unsigned int val;
138
139	/* Do not do the fixup on other platforms! */
140	if (!machine_is(gef_sbc610))
141		return;
142
143	printk(KERN_INFO "Running NEC uPD720101 Fixup\n");
144
145	/* Ensure ports 1, 2, 3, 4 & 5 are enabled */
146	pci_read_config_dword(pdev, 0xe0, &val);
147	pci_write_config_dword(pdev, 0xe0, (val & ~7) | 0x5);
148
149	/* System clock is 48-MHz Oscillator and EHCI Enabled. */
150	pci_write_config_dword(pdev, 0xe4, 1 << 5);
151}
152DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_USB,
153	gef_sbc610_nec_fixup);
154
155machine_arch_initcall(gef_sbc610, mpc86xx_common_publish_devices);
156
157define_machine(gef_sbc610) {
158	.name			= "GE SBC610",
159	.compatible		= "gef,sbc610",
160	.setup_arch		= gef_sbc610_setup_arch,
161	.init_IRQ		= gef_sbc610_init_irq,
162	.show_cpuinfo		= gef_sbc610_show_cpuinfo,
163	.get_irq		= mpic_get_irq,
164	.time_init		= mpc86xx_time_init,
165	.progress		= udbg_progress,
166#ifdef CONFIG_PCI
167	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
168#endif
169};