pmp8074.dtsi

  1// SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause
  2
  3#include <dt-bindings/spmi/spmi.h>
  4#include <dt-bindings/iio/qcom,spmi-vadc.h>
  5
  6&spmi_bus {
  7	pmic@0 {
  8		compatible = "qcom,pmp8074", "qcom,spmi-pmic";
  9		reg = <0x0 SPMI_USID>;
 10		#address-cells = <1>;
 11		#size-cells = <0>;
 12
 13		pmp8074_adc: adc@3100 {
 14			compatible = "qcom,spmi-adc-rev2";
 15			reg = <0x3100>;
 16			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
 17			#address-cells = <1>;
 18			#size-cells = <0>;
 19			#io-channel-cells = <1>;
 20
 21			channel@0 {
 22				reg = <ADC5_REF_GND>;
 23				qcom,pre-scaling = <1 1>;
 24				label = "ref_gnd";
 25			};
 26
 27			channel@1 {
 28				reg = <ADC5_1P25VREF>;
 29				qcom,pre-scaling = <1 1>;
 30				label = "vref_1p25";
 31			};
 32
 33			channel@2 {
 34				reg = <ADC5_VREF_VADC>;
 35				qcom,pre-scaling = <1 1>;
 36				label = "vref_vadc";
 37			};
 38
 39			channel@6 {
 40				reg = <ADC5_DIE_TEMP>;
 41				qcom,pre-scaling = <1 1>;
 42				label = "pmic_die";
 43			};
 44
 45			channel@76 {
 46				reg = <ADC5_XO_THERM_100K_PU>;
 47				qcom,ratiometric;
 48				qcom,hw-settle-time = <200>;
 49				qcom,pre-scaling = <1 1>;
 50				label = "xo_therm";
 51			};
 52
 53			channel@77 {
 54				reg = <ADC5_AMUX_THM1_100K_PU>;
 55				qcom,ratiometric;
 56				qcom,hw-settle-time = <200>;
 57				qcom,pre-scaling = <1 1>;
 58				label = "pa_therm1";
 59			};
 60
 61			channel@78 {
 62				reg = <ADC5_AMUX_THM2_100K_PU>;
 63				qcom,ratiometric;
 64				qcom,hw-settle-time = <200>;
 65				qcom,pre-scaling = <1 1>;
 66				label = "pa_therm2";
 67			};
 68
 69			channel@79 {
 70				reg = <ADC5_AMUX_THM3_100K_PU>;
 71				qcom,ratiometric;
 72				qcom,hw-settle-time = <200>;
 73				qcom,pre-scaling = <1 1>;
 74				label = "pa_therm3";
 75			};
 76
 77			channel@131 {
 78				reg = <ADC5_VPH_PWR>;
 79				qcom,pre-scaling = <1 3>;
 80				label = "vph_pwr";
 81			};
 82		};
 83
 84		pmp8074_rtc: rtc@6000 {
 85			compatible = "qcom,pm8941-rtc";
 86			reg = <0x6000>, <0x6100>;
 87			reg-names = "rtc", "alarm";
 88			interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
 89			allow-set-time;
 90			status = "disabled";
 91		};
 92
 93		pmp8074_gpios: gpio@c000 {
 94			compatible = "qcom,pmp8074-gpio", "qcom,spmi-gpio";
 95			reg = <0xc000>;
 96			gpio-controller;
 97			#gpio-cells = <2>;
 98			gpio-ranges = <&pmp8074_gpios 0 0 12>;
 99			interrupt-controller;
100			#interrupt-cells = <2>;
101		};
102	};
103
104	pmic@1 {
105		compatible = "qcom,pmp8074", "qcom,spmi-pmic";
106		reg = <0x1 SPMI_USID>;
107
108		regulators {
109			compatible = "qcom,pmp8074-regulators";
110
111			s3: s3 {
112				regulator-name = "vdd_s3";
113				regulator-min-microvolt = <592000>;
114				regulator-max-microvolt = <1064000>;
115				regulator-always-on;
116				regulator-boot-on;
117			};
118
119			s4: s4 {
120				regulator-name = "vdd_s4";
121				regulator-min-microvolt = <712000>;
122				regulator-max-microvolt = <992000>;
123				regulator-always-on;
124				regulator-boot-on;
125			};
126
127			l11: l11 {
128				regulator-name = "l11";
129				regulator-min-microvolt = <1800000>;
130				regulator-max-microvolt = <3300000>;
131			};
132		};
133	};
134};