pmm8155au_2.dtsi

  1// SPDX-License-Identifier: BSD-3-Clause
  2/*
  3 * Copyright (c) 2021, Linaro Limited
  4 */
  5
  6#include <dt-bindings/input/input.h>
  7#include <dt-bindings/interrupt-controller/irq.h>
  8#include <dt-bindings/spmi/spmi.h>
  9
 10/ {
 11	thermal-zones {
 12		pmm8155au-2-thermal {
 13			polling-delay-passive = <100>;
 14
 15			thermal-sensors = <&pmm8155au_2_temp>;
 16
 17			trips {
 18				trip0 {
 19					temperature = <95000>;
 20					hysteresis = <0>;
 21					type = "passive";
 22				};
 23
 24				trip1 {
 25					temperature = <115000>;
 26					hysteresis = <0>;
 27					type = "hot";
 28				};
 29
 30				trip2 {
 31					temperature = <145000>;
 32					hysteresis = <0>;
 33					type = "critical";
 34				};
 35			};
 36		};
 37	};
 38};
 39
 40&spmi_bus {
 41	pmic@4 {
 42		compatible = "qcom,pmm8155au", "qcom,spmi-pmic";
 43		reg = <0x4 SPMI_USID>;
 44		#address-cells = <1>;
 45		#size-cells = <0>;
 46
 47		pon@800 {
 48			compatible = "qcom,pm8916-pon";
 49			reg = <0x0800>;
 50
 51			status = "disabled";
 52		};
 53
 54		pmm8155au_2_temp: temp-alarm@2400 {
 55			compatible = "qcom,spmi-temp-alarm";
 56			reg = <0x2400>;
 57			interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
 58			io-channels = <&pmm8155au_2_adc ADC5_DIE_TEMP>;
 59			io-channel-names = "thermal";
 60			#thermal-sensor-cells = <0>;
 61		};
 62
 63		pmm8155au_2_adc: adc@3100 {
 64			compatible = "qcom,spmi-adc5";
 65			reg = <0x3100>;
 66			#address-cells = <1>;
 67			#size-cells = <0>;
 68			#io-channel-cells = <1>;
 69			interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
 70
 71			channel@0 {
 72				reg = <ADC5_REF_GND>;
 73				qcom,pre-scaling = <1 1>;
 74				label = "ref_gnd";
 75			};
 76
 77			channel@1 {
 78				reg = <ADC5_1P25VREF>;
 79				qcom,pre-scaling = <1 1>;
 80				label = "vref_1p25";
 81			};
 82
 83			channel@6 {
 84				reg = <ADC5_DIE_TEMP>;
 85				qcom,pre-scaling = <1 1>;
 86				label = "die_temp";
 87			};
 88		};
 89
 90		pmm8155au_2_gpios: gpio@c000 {
 91			compatible = "qcom,pmm8155au-gpio", "qcom,spmi-gpio";
 92			reg = <0xc000>;
 93			gpio-controller;
 94			#gpio-cells = <2>;
 95			gpio-ranges = <&pmm8155au_2_gpios 0 0 10>;
 96			interrupt-controller;
 97			#interrupt-cells = <2>;
 98		};
 99	};
100
101	pmic@5 {
102		compatible = "qcom,pmm8155au", "qcom,spmi-pmic";
103		reg = <0x5 SPMI_USID>;
104		#address-cells = <1>;
105		#size-cells = <0>;
106	};
107};