pm8994.dtsi

  1// SPDX-License-Identifier: GPL-2.0
  2#include <dt-bindings/iio/qcom,spmi-vadc.h>
  3#include <dt-bindings/input/linux-event-codes.h>
  4#include <dt-bindings/interrupt-controller/irq.h>
  5#include <dt-bindings/spmi/spmi.h>
  6
  7/ {
  8	thermal-zones {
  9		pm8994-thermal {
 10			polling-delay-passive = <250>;
 11
 12			thermal-sensors = <&pm8994_temp>;
 13
 14			trips {
 15				pm8994_alert0: pm8994-alert0 {
 16					temperature = <95000>;
 17					hysteresis = <2000>;
 18					type = "passive";
 19				};
 20				pm8994_crit: pm8994-crit {
 21					temperature = <125000>;
 22					hysteresis = <2000>;
 23					type = "critical";
 24				};
 25			};
 26		};
 27	};
 28};
 29
 30&spmi_bus {
 31
 32	pmic@0 {
 33		compatible = "qcom,pm8994", "qcom,spmi-pmic";
 34		reg = <0x0 SPMI_USID>;
 35		#address-cells = <1>;
 36		#size-cells = <0>;
 37
 38		rtc@6000 {
 39			compatible = "qcom,pm8941-rtc";
 40			reg = <0x6000>, <0x6100>;
 41			reg-names = "rtc", "alarm";
 42			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
 43		};
 44
 45		pm8994_pon: pon@800 {
 46			compatible = "qcom,pm8916-pon";
 47			reg = <0x800>;
 48			mode-bootloader = <0x2>;
 49			mode-recovery = <0x1>;
 50
 51			pwrkey {
 52				compatible = "qcom,pm8941-pwrkey";
 53				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
 54				debounce = <15625>;
 55				bias-pull-up;
 56				linux,code = <KEY_POWER>;
 57			};
 58
 59			pm8994_resin: resin {
 60				compatible = "qcom,pm8941-resin";
 61				interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
 62				debounce = <15625>;
 63				bias-pull-up;
 64				status = "disabled";
 65			};
 66		};
 67
 68		pm8994_temp: temp-alarm@2400 {
 69			compatible = "qcom,spmi-temp-alarm";
 70			reg = <0x2400>;
 71			interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
 72			io-channels = <&pm8994_vadc VADC_DIE_TEMP>;
 73			io-channel-names = "thermal";
 74			#thermal-sensor-cells = <0>;
 75		};
 76
 77		pm8994_vadc: adc@3100 {
 78			compatible = "qcom,spmi-vadc";
 79			reg = <0x3100>;
 80			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
 81			#address-cells = <1>;
 82			#size-cells = <0>;
 83			#io-channel-cells = <1>;
 84
 85			channel@7 {
 86				reg = <VADC_VSYS>;
 87				qcom,pre-scaling = <1 3>;
 88				label = "vph_pwr";
 89			};
 90			channel@8 {
 91				reg = <VADC_DIE_TEMP>;
 92				label = "die_temp";
 93			};
 94			channel@9 {
 95				reg = <VADC_REF_625MV>;
 96				label = "ref_625mv";
 97			};
 98			channel@a {
 99				reg = <VADC_REF_1250MV>;
100				label = "ref_1250mv";
101			};
102			channel@e {
103				reg = <VADC_GND_REF>;
104			};
105			channel@f {
106				reg = <VADC_VDD_VADC>;
107			};
108		};
109
110		pm8994_gpios: gpio@c000 {
111			compatible = "qcom,pm8994-gpio", "qcom,spmi-gpio";
112			reg = <0xc000>;
113			gpio-controller;
114			gpio-ranges = <&pm8994_gpios 0 0 22>;
115			#gpio-cells = <2>;
116			interrupt-controller;
117			#interrupt-cells = <2>;
118		};
119
120		pm8994_mpps: mpps@a000 {
121			compatible = "qcom,pm8994-mpp", "qcom,spmi-mpp";
122			reg = <0xa000>;
123			gpio-controller;
124			#gpio-cells = <2>;
125			gpio-ranges = <&pm8994_mpps 0 0 8>;
126			interrupt-controller;
127			#interrupt-cells = <2>;
128		};
129	};
130
131	pmic@1 {
132		compatible = "qcom,pm8994", "qcom,spmi-pmic";
133		reg = <0x1 SPMI_USID>;
134		#address-cells = <1>;
135		#size-cells = <0>;
136
137		pm8994_lpg: pwm {
138			compatible = "qcom,pm8994-lpg";
139
140			#address-cells = <1>;
141			#size-cells = <0>;
142			#pwm-cells = <2>;
143
144			status = "disabled";
145		};
146
147		pm8994_spmi_regulators: regulators {
148			compatible = "qcom,pm8994-regulators";
149		};
150	};
151};