pm8150l.dtsi

  1// SPDX-License-Identifier: BSD-3-Clause
  2/*
  3 * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
  4 * Copyright (c) 2019, Linaro Limited
  5 */
  6
  7#include <dt-bindings/iio/qcom,spmi-vadc.h>
  8#include <dt-bindings/interrupt-controller/irq.h>
  9#include <dt-bindings/spmi/spmi.h>
 10
 11/ {
 12	thermal-zones {
 13		pm8150l-thermal {
 14			polling-delay-passive = <100>;
 15
 16			thermal-sensors = <&pm8150l_temp>;
 17
 18			trips {
 19				trip0 {
 20					temperature = <95000>;
 21					hysteresis = <0>;
 22					type = "passive";
 23				};
 24
 25				trip1 {
 26					temperature = <115000>;
 27					hysteresis = <0>;
 28					type = "hot";
 29				};
 30
 31				trip2 {
 32					temperature = <145000>;
 33					hysteresis = <0>;
 34					type = "critical";
 35				};
 36			};
 37		};
 38	};
 39};
 40
 41&spmi_bus {
 42	pmic@4 {
 43		compatible = "qcom,pm8150l", "qcom,spmi-pmic";
 44		reg = <0x4 SPMI_USID>;
 45		#address-cells = <1>;
 46		#size-cells = <0>;
 47
 48		pon@800 {
 49			compatible = "qcom,pm8916-pon";
 50			reg = <0x0800>;
 51
 52			status = "disabled";
 53		};
 54
 55		pm8150l_temp: temp-alarm@2400 {
 56			compatible = "qcom,spmi-temp-alarm";
 57			reg = <0x2400>;
 58			interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
 59			io-channels = <&pm8150l_adc ADC5_DIE_TEMP>;
 60			io-channel-names = "thermal";
 61			#thermal-sensor-cells = <0>;
 62		};
 63
 64		pm8150l_adc: adc@3100 {
 65			compatible = "qcom,spmi-adc5";
 66			reg = <0x3100>;
 67			#address-cells = <1>;
 68			#size-cells = <0>;
 69			#io-channel-cells = <1>;
 70			interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
 71
 72			channel@0 {
 73				reg = <ADC5_REF_GND>;
 74				qcom,pre-scaling = <1 1>;
 75				label = "ref_gnd";
 76			};
 77
 78			channel@1 {
 79				reg = <ADC5_1P25VREF>;
 80				qcom,pre-scaling = <1 1>;
 81				label = "vref_1p25";
 82			};
 83
 84			channel@6 {
 85				reg = <ADC5_DIE_TEMP>;
 86				qcom,pre-scaling = <1 1>;
 87				label = "die_temp";
 88			};
 89		};
 90
 91		pm8150l_adc_tm: adc-tm@3500 {
 92			compatible = "qcom,spmi-adc-tm5";
 93			reg = <0x3500>;
 94			interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
 95			#thermal-sensor-cells = <1>;
 96			#address-cells = <1>;
 97			#size-cells = <0>;
 98			status = "disabled";
 99		};
100
101		pm8150l_gpios: gpio@c000 {
102			compatible = "qcom,pm8150l-gpio", "qcom,spmi-gpio";
103			reg = <0xc000>;
104			gpio-controller;
105			gpio-ranges = <&pm8150l_gpios 0 0 12>;
106			#gpio-cells = <2>;
107			interrupt-controller;
108			#interrupt-cells = <2>;
109		};
110	};
111
112	pmic@5 {
113		compatible = "qcom,pm8150l", "qcom,spmi-pmic";
114		reg = <0x5 SPMI_USID>;
115		#address-cells = <1>;
116		#size-cells = <0>;
117
118		pm8150l_flash: led-controller@d300 {
119			compatible = "qcom,pm8150l-flash-led", "qcom,spmi-flash-led";
120			reg = <0xd300>;
121			status = "disabled";
122		};
123
124		pm8150l_lpg: pwm {
125			compatible = "qcom,pm8150l-lpg";
126
127			#address-cells = <1>;
128			#size-cells = <0>;
129			#pwm-cells = <2>;
130
131			status = "disabled";
132		};
133
134		pm8150l_wled: leds@d800 {
135			compatible = "qcom,pm8150l-wled";
136			reg = <0xd800>, <0xd900>;
137			interrupts = <0x5 0xd8 0x1 IRQ_TYPE_EDGE_RISING>,
138				     <0x5 0xd8 0x2 IRQ_TYPE_EDGE_RISING>;
139			interrupt-names = "ovp", "short";
140			label = "backlight";
141
142			status = "disabled";
143		};
144	};
145};