pm8150.dtsi

  1// SPDX-License-Identifier: BSD-3-Clause
  2/*
  3 * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
  4 * Copyright (c) 2019, Linaro Limited
  5 */
  6
  7#include <dt-bindings/input/input.h>
  8#include <dt-bindings/interrupt-controller/irq.h>
  9#include <dt-bindings/spmi/spmi.h>
 10#include <dt-bindings/iio/qcom,spmi-vadc.h>
 11
 12/ {
 13	thermal-zones {
 14		pm8150-thermal {
 15			polling-delay-passive = <100>;
 16
 17			thermal-sensors = <&pm8150_temp>;
 18
 19			trips {
 20				trip0 {
 21					temperature = <95000>;
 22					hysteresis = <0>;
 23					type = "passive";
 24				};
 25
 26				trip1 {
 27					temperature = <115000>;
 28					hysteresis = <0>;
 29					type = "hot";
 30				};
 31
 32				trip2 {
 33					temperature = <145000>;
 34					hysteresis = <0>;
 35					type = "critical";
 36				};
 37			};
 38		};
 39	};
 40};
 41
 42&spmi_bus {
 43	pm8150_0: pmic@0 {
 44		compatible = "qcom,pm8150", "qcom,spmi-pmic";
 45		reg = <0x0 SPMI_USID>;
 46		#address-cells = <1>;
 47		#size-cells = <0>;
 48
 49		pon: pon@800 {
 50			compatible = "qcom,pm8998-pon";
 51			reg = <0x0800>;
 52
 53			pon_pwrkey: pwrkey {
 54				compatible = "qcom,pm8941-pwrkey";
 55				interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
 56				debounce = <15625>;
 57				bias-pull-up;
 58				linux,code = <KEY_POWER>;
 59
 60				status = "disabled";
 61			};
 62
 63			pon_resin: resin {
 64				compatible = "qcom,pm8941-resin";
 65				interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>;
 66				debounce = <15625>;
 67				bias-pull-up;
 68
 69				status = "disabled";
 70			};
 71		};
 72
 73		pm8150_temp: temp-alarm@2400 {
 74			compatible = "qcom,spmi-temp-alarm";
 75			reg = <0x2400>;
 76			interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
 77			io-channels = <&pm8150_adc ADC5_DIE_TEMP>;
 78			io-channel-names = "thermal";
 79			#thermal-sensor-cells = <0>;
 80		};
 81
 82		pm8150_adc: adc@3100 {
 83			compatible = "qcom,spmi-adc5";
 84			reg = <0x3100>;
 85			#address-cells = <1>;
 86			#size-cells = <0>;
 87			#io-channel-cells = <1>;
 88			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
 89
 90			channel@0 {
 91				reg = <ADC5_REF_GND>;
 92				qcom,pre-scaling = <1 1>;
 93				label = "ref_gnd";
 94			};
 95
 96			channel@1 {
 97				reg = <ADC5_1P25VREF>;
 98				qcom,pre-scaling = <1 1>;
 99				label = "vref_1p25";
100			};
101
102			channel@6 {
103				reg = <ADC5_DIE_TEMP>;
104				qcom,pre-scaling = <1 1>;
105				label = "die_temp";
106			};
107		};
108
109		pm8150_adc_tm: adc-tm@3500 {
110			compatible = "qcom,spmi-adc-tm5";
111			reg = <0x3500>;
112			interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
113			#thermal-sensor-cells = <1>;
114			#address-cells = <1>;
115			#size-cells = <0>;
116			status = "disabled";
117		};
118
119		rtc@6000 {
120			compatible = "qcom,pm8941-rtc";
121			reg = <0x6000>, <0x6100>;
122			reg-names = "rtc", "alarm";
123			interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
124		};
125
126		pm8150_gpios: gpio@c000 {
127			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
128			reg = <0xc000>;
129			gpio-controller;
130			gpio-ranges = <&pm8150_gpios 0 0 10>;
131			#gpio-cells = <2>;
132			interrupt-controller;
133			#interrupt-cells = <2>;
134		};
135	};
136
137	pmic@1 {
138		compatible = "qcom,pm8150", "qcom,spmi-pmic";
139		reg = <0x1 SPMI_USID>;
140		#address-cells = <1>;
141		#size-cells = <0>;
142	};
143};