pm6125.dtsi

  1// SPDX-License-Identifier: BSD-3-Clause
  2
  3#include <dt-bindings/iio/qcom,spmi-vadc.h>
  4#include <dt-bindings/input/input.h>
  5#include <dt-bindings/input/linux-event-codes.h>
  6#include <dt-bindings/interrupt-controller/irq.h>
  7#include <dt-bindings/spmi/spmi.h>
  8
  9/ {
 10	thermal-zones {
 11		pm6125-thermal {
 12			polling-delay-passive = <100>;
 13
 14			thermal-sensors = <&pm6125_temp>;
 15
 16			trips {
 17				trip0 {
 18					temperature = <95000>;
 19					hysteresis = <0>;
 20					type = "passive";
 21				};
 22
 23				trip1 {
 24					temperature = <115000>;
 25					hysteresis = <0>;
 26					type = "hot";
 27				};
 28
 29				trip2 {
 30					temperature = <145000>;
 31					hysteresis = <0>;
 32					type = "critical";
 33				};
 34			};
 35		};
 36	};
 37};
 38
 39&spmi_bus {
 40	pmic@0 {
 41		compatible = "qcom,pm6125", "qcom,spmi-pmic";
 42		reg = <0x0 SPMI_USID>;
 43		#address-cells = <1>;
 44		#size-cells = <0>;
 45
 46		pm6125_pon: pon@800 {
 47			compatible = "qcom,pm8998-pon";
 48			reg = <0x800>;
 49			mode-bootloader = <0x2>;
 50			mode-recovery = <0x1>;
 51
 52			pon_pwrkey: pwrkey {
 53				compatible = "qcom,pm8941-pwrkey";
 54				interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
 55				debounce = <15625>;
 56				linux,code = <KEY_POWER>;
 57				bias-pull-up;
 58				status = "disabled";
 59			};
 60
 61			pon_resin: resin {
 62				compatible = "qcom,pm8941-resin";
 63				interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>;
 64				debounce = <15625>;
 65				bias-pull-up;
 66				status = "disabled";
 67			};
 68		};
 69
 70		pm6125_temp: temp-alarm@2400 {
 71			compatible = "qcom,spmi-temp-alarm";
 72			reg = <0x2400>;
 73			interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
 74			io-channels = <&pm6125_adc ADC5_DIE_TEMP>;
 75			io-channel-names = "thermal";
 76			#thermal-sensor-cells = <0>;
 77		};
 78
 79		pm6125_adc: adc@3100 {
 80			compatible = "qcom,spmi-adc5";
 81			reg = <0x3100>;
 82			#address-cells = <1>;
 83			#size-cells = <0>;
 84			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
 85			#io-channel-cells = <1>;
 86
 87			channel@0 {
 88				reg = <ADC5_REF_GND>;
 89				qcom,pre-scaling = <1 1>;
 90				label = "ref_gnd";
 91			};
 92
 93			channel@1 {
 94				reg = <ADC5_1P25VREF>;
 95				qcom,pre-scaling = <1 1>;
 96				label = "vref_1p25";
 97			};
 98
 99			channel@6 {
100				reg = <ADC5_DIE_TEMP>;
101				qcom,pre-scaling = <1 1>;
102				label = "die_temp";
103			};
104
105			channel@83 {
106				reg = <ADC5_VPH_PWR>;
107				qcom,pre-scaling = <1 3>;
108				label = "vph_pwr";
109			};
110
111			channel@85 {
112				reg = <ADC5_VCOIN>;
113				qcom,pre-scaling = <1 3>;
114				label = "vcoin";
115			};
116
117			channel@4c {
118				reg = <ADC5_XO_THERM_100K_PU>;
119				qcom,pre-scaling = <1 1>;
120				qcom,hw-settle-time = <200>;
121				qcom,ratiometric;
122				label = "xo_therm";
123			};
124		};
125
126		pm6125_adc_tm: adc-tm@3500 {
127			compatible = "qcom,spmi-adc-tm5";
128			reg = <0x3500>;
129			interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
130			#address-cells = <1>;
131			#size-cells = <0>;
132			#thermal-sensor-cells = <1>;
133			status = "disabled";
134		};
135
136		pm6125_rtc: rtc@6000 {
137			compatible = "qcom,pm8941-rtc";
138			reg = <0x6000>, <0x6100>;
139			reg-names = "rtc", "alarm";
140			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
141			status = "disabled";
142		};
143
144		pm6125_gpios: gpio@c000 {
145			compatible = "qcom,pm6125-gpio", "qcom,spmi-gpio";
146			reg = <0xc000>;
147			gpio-controller;
148			gpio-ranges = <&pm6125_gpios 0 0 9>;
149			#gpio-cells = <2>;
150			interrupt-controller;
151			#interrupt-cells = <2>;
152		};
153	};
154
155	pmic@1 {
156		compatible = "qcom,pm6125", "qcom,spmi-pmic";
157		reg = <0x1 SPMI_USID>;
158	};
159};