pm8226.dtsi

  1// SPDX-License-Identifier: BSD-3-Clause
  2#include <dt-bindings/iio/qcom,spmi-vadc.h>
  3#include <dt-bindings/input/linux-event-codes.h>
  4#include <dt-bindings/interrupt-controller/irq.h>
  5#include <dt-bindings/spmi/spmi.h>
  6
  7/ {
  8	thermal-zones {
  9		pm8226-thermal {
 10			polling-delay-passive = <100>;
 11			polling-delay = <0>;
 12			thermal-sensors = <&pm8226_temp>;
 13
 14			trips {
 15				trip0 {
 16					temperature = <105000>;
 17					hysteresis = <2000>;
 18					type = "passive";
 19				};
 20
 21				trip1 {
 22					temperature = <125000>;
 23					hysteresis = <2000>;
 24					type = "hot";
 25				};
 26
 27				crit {
 28					temperature = <145000>;
 29					hysteresis = <2000>;
 30					type = "critical";
 31				};
 32			};
 33		};
 34	};
 35};
 36
 37&spmi_bus {
 38	pm8226_0: pm8226@0 {
 39		compatible = "qcom,pm8226", "qcom,spmi-pmic";
 40		reg = <0x0 SPMI_USID>;
 41		#address-cells = <1>;
 42		#size-cells = <0>;
 43
 44		pon@800 {
 45			compatible = "qcom,pm8916-pon";
 46			reg = <0x800>;
 47
 48			pwrkey {
 49				compatible = "qcom,pm8941-pwrkey";
 50				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
 51				debounce = <15625>;
 52				bias-pull-up;
 53				linux,code = <KEY_POWER>;
 54			};
 55
 56			pm8226_resin: resin {
 57				compatible = "qcom,pm8941-resin";
 58				interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
 59				debounce = <15625>;
 60				bias-pull-up;
 61				status = "disabled";
 62			};
 63		};
 64
 65		smbb: charger@1000 {
 66			compatible = "qcom,pm8226-charger";
 67			reg = <0x1000>;
 68			interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
 69				     <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
 70				     <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
 71				     <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
 72				     <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
 73				     <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
 74				     <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
 75				     <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
 76			interrupt-names = "chg-done",
 77					  "chg-fast",
 78					  "chg-trkl",
 79					  "bat-temp-ok",
 80					  "bat-present",
 81					  "chg-gone",
 82					  "usb-valid",
 83					  "dc-valid";
 84
 85			status = "disabled";
 86
 87			chg_otg: otg-vbus { };
 88		};
 89
 90		pm8226_temp: temp-alarm@2400 {
 91			compatible = "qcom,spmi-temp-alarm";
 92			reg = <0x2400>;
 93			interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
 94			io-channels = <&pm8226_vadc VADC_DIE_TEMP>;
 95			io-channel-names = "thermal";
 96			#thermal-sensor-cells = <0>;
 97		};
 98
 99		pm8226_vadc: adc@3100 {
100			compatible = "qcom,spmi-vadc";
101			reg = <0x3100>;
102			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
103			#address-cells = <1>;
104			#size-cells = <0>;
105			#io-channel-cells = <1>;
106
107			channel@7 {
108				reg = <VADC_VSYS>;
109				qcom,pre-scaling = <1 3>;
110				label = "vph_pwr";
111			};
112			channel@8 {
113				reg = <VADC_DIE_TEMP>;
114				label = "die_temp";
115			};
116			channel@9 {
117				reg = <VADC_REF_625MV>;
118				label = "ref_625mv";
119			};
120			channel@a {
121				reg = <VADC_REF_1250MV>;
122				label = "ref_1250mv";
123			};
124			channel@e {
125				reg = <VADC_GND_REF>;
126			};
127			channel@f {
128				reg = <VADC_VDD_VADC>;
129			};
130		};
131
132		pm8226_iadc: adc@3600 {
133			compatible = "qcom,pm8226-iadc", "qcom,spmi-iadc";
134			reg = <0x3600>;
135			interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
136		};
137
138		rtc@6000 {
139			compatible = "qcom,pm8941-rtc";
140			reg = <0x6000>, <0x6100>;
141			reg-names = "rtc", "alarm";
142			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
143		};
144
145		pm8226_mpps: mpps@a000 {
146			compatible = "qcom,pm8226-mpp", "qcom,spmi-mpp";
147			reg = <0xa000>;
148			gpio-controller;
149			#gpio-cells = <2>;
150			gpio-ranges = <&pm8226_mpps 0 0 8>;
151			interrupt-controller;
152			#interrupt-cells = <2>;
153		};
154
155		pm8226_gpios: gpio@c000 {
156			compatible = "qcom,pm8226-gpio", "qcom,spmi-gpio";
157			reg = <0xc000>;
158			gpio-controller;
159			#gpio-cells = <2>;
160			gpio-ranges = <&pm8226_gpios 0 0 8>;
161			interrupt-controller;
162			#interrupt-cells = <2>;
163		};
164	};
165
166	pm8226_1: pm8226@1 {
167		compatible = "qcom,pm8226", "qcom,spmi-pmic";
168		reg = <0x1 SPMI_USID>;
169		#address-cells = <1>;
170		#size-cells = <0>;
171
172		pm8226_spmi_regulators: regulators {
173			compatible = "qcom,pm8226-regulators";
174		};
175
176		pm8226_vib: vibrator@c000 {
177			compatible = "qcom,pm8916-vib";
178			reg = <0xc000>;
179			status = "disabled";
180		};
181	};
182};