imx6dl-yapp43-common.dtsi

  1// SPDX-License-Identifier: GPL-2.0
  2//
  3// Copyright (C) 2021 Y Soft Corporation, a.s.
  4
  5#include <dt-bindings/gpio/gpio.h>
  6#include <dt-bindings/interrupt-controller/irq.h>
  7#include <dt-bindings/input/input.h>
  8#include <dt-bindings/leds/common.h>
  9#include <dt-bindings/pwm/pwm.h>
 10
 11/ {
 12	aliases: aliases {
 13		ethernet1 = &eth1;
 14		ethernet2 = &eth2;
 15		mmc0 = &usdhc3;
 16		mmc1 = &usdhc4;
 17	};
 18
 19	backlight: backlight {
 20		compatible = "pwm-backlight";
 21		pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
 22		brightness-levels = <0 32 64 128 255>;
 23		default-brightness-level = <32>;
 24		num-interpolated-steps = <8>;
 25		power-supply = <&sw2_reg>;
 26		status = "disabled";
 27	};
 28
 29	beeper: beeper {
 30		compatible = "pwm-beeper";
 31		pwms = <&pwm3 0 500000 0>;
 32		status = "disabled";
 33	};
 34
 35	gpio_keys: gpio-keys {
 36		compatible = "gpio-keys";
 37		pinctrl-names = "default";
 38		pinctrl-0 = <&pinctrl_gpio_keys>;
 39		status = "disabled";
 40
 41		button {
 42			label = "Factory RESET";
 43			linux,code = <BTN_0>;
 44			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
 45		};
 46	};
 47
 48	lcd_display: display {
 49		compatible = "fsl,imx-parallel-display";
 50		#address-cells = <1>;
 51		#size-cells = <0>;
 52		interface-pix-fmt = "rgb24";
 53		pinctrl-names = "default";
 54		pinctrl-0 = <&pinctrl_ipu1>;
 55		status = "disabled";
 56
 57		port@0 {
 58			reg = <0>;
 59
 60			lcd_display_in: endpoint {
 61				remote-endpoint = <&ipu1_di0_disp0>;
 62			};
 63		};
 64
 65		port@1 {
 66			reg = <1>;
 67
 68			lcd_display_out: endpoint {
 69				remote-endpoint = <&lcd_panel_in>;
 70			};
 71		};
 72	};
 73
 74	panel: panel {
 75		compatible = "dataimage,scf0700c48ggu18";
 76		power-supply = <&sw2_reg>;
 77		backlight = <&backlight>;
 78		enable-gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
 79		status = "disabled";
 80
 81		port {
 82			lcd_panel_in: endpoint {
 83				remote-endpoint = <&lcd_display_out>;
 84			};
 85		};
 86	};
 87
 88	reg_usb_h1_vbus: regulator-usb-h1-vbus {
 89		compatible = "regulator-fixed";
 90		pinctrl-names = "default";
 91		pinctrl-0 = <&pinctrl_usbh1_vbus>;
 92		regulator-name = "usb_h1_vbus";
 93		regulator-min-microvolt = <5000000>;
 94		regulator-max-microvolt = <5000000>;
 95		gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
 96		enable-active-high;
 97		status = "disabled";
 98	};
 99
100	reg_usb_otg_vbus: regulator-usb-otg-vbus {
101		compatible = "regulator-fixed";
102		pinctrl-names = "default";
103		pinctrl-0 = <&pinctrl_usbotg_vbus>;
104		regulator-name = "usb_otg_vbus";
105		regulator-min-microvolt = <5000000>;
106		regulator-max-microvolt = <5000000>;
107		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
108		enable-active-high;
109	};
110};
111
112&fec {
113	pinctrl-names = "default";
114	pinctrl-0 = <&pinctrl_enet>;
115	phy-mode = "rgmii-id";
116	phy-supply = <&sw2_reg>;
117	status = "okay";
118
119	fixed-link {
120		speed = <1000>;
121		full-duplex;
122	};
123
124	mdio {
125		#address-cells = <1>;
126		#size-cells = <0>;
127
128		switch@0 {
129			compatible = "marvell,mv88e6085";
130			reg = <0>;
131			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
132
133			switch_ports: ports {
134				#address-cells = <1>;
135				#size-cells = <0>;
136
137				ethphy0: port@0 {
138					reg = <0>;
139					label = "cpu";
140					phy-mode = "rgmii-id";
141					ethernet = <&fec>;
142
143					fixed-link {
144						speed = <1000>;
145						full-duplex;
146					};
147				};
148
149				eth2: port@1 {
150					reg = <1>;
151					label = "eth2";
152					phy-handle = <&phy_port1>;
153				};
154
155				eth1: port@2 {
156					reg = <2>;
157					label = "eth1";
158					phy-handle = <&phy_port2>;
159				};
160			};
161
162			mdio {
163				#address-cells = <1>;
164				#size-cells = <0>;
165
166				phy_port1: switchphy@11 {
167					reg = <0x11>;
168				};
169
170				phy_port2: switchphy@12 {
171					reg = <0x12>;
172				};
173			};
174		};
175	};
176};
177
178&i2c2 {
179	clock-frequency = <100000>;
180	pinctrl-names = "default";
181	pinctrl-0 = <&pinctrl_i2c2>;
182	status = "okay";
183
184	pmic@8 {
185		compatible = "fsl,pfuze200";
186		pinctrl-names = "default";
187		pinctrl-0 = <&pinctrl_pmic>;
188		reg = <0x8>;
189
190		regulators {
191			sw1a_reg: sw1ab {
192				regulator-min-microvolt = <300000>;
193				regulator-max-microvolt = <1875000>;
194				regulator-boot-on;
195				regulator-always-on;
196				regulator-ramp-delay = <6250>;
197			};
198
199			sw2_reg: sw2 {
200				regulator-min-microvolt = <800000>;
201				regulator-max-microvolt = <3300000>;
202				regulator-boot-on;
203				regulator-always-on;
204			};
205
206			sw3a_reg: sw3a {
207				regulator-min-microvolt = <400000>;
208				regulator-max-microvolt = <1975000>;
209				regulator-boot-on;
210				regulator-always-on;
211			};
212
213			sw3b_reg: sw3b {
214				regulator-min-microvolt = <400000>;
215				regulator-max-microvolt = <1975000>;
216				regulator-boot-on;
217				regulator-always-on;
218			};
219
220			swbst_reg: swbst {
221				regulator-min-microvolt = <5000000>;
222				regulator-max-microvolt = <5150000>;
223			};
224
225			vgen1_reg: vgen1 {
226				regulator-min-microvolt = <800000>;
227				regulator-max-microvolt = <1550000>;
228			};
229
230			vgen2_reg: vgen2 {
231				regulator-min-microvolt = <800000>;
232				regulator-max-microvolt = <1550000>;
233			};
234
235			vgen3_reg: vgen3 {
236				regulator-min-microvolt = <1800000>;
237				regulator-max-microvolt = <3300000>;
238				regulator-always-on;
239			};
240
241			vgen4_reg: vgen4 {
242				regulator-min-microvolt = <1800000>;
243				regulator-max-microvolt = <3300000>;
244				regulator-always-on;
245			};
246
247			vgen5_reg: vgen5 {
248				regulator-min-microvolt = <1800000>;
249				regulator-max-microvolt = <3300000>;
250				regulator-always-on;
251			};
252
253			vgen6_reg: vgen6 {
254				regulator-min-microvolt = <1800000>;
255				regulator-max-microvolt = <3300000>;
256				regulator-always-on;
257			};
258
259			vref_reg: vrefddr {
260				regulator-boot-on;
261				regulator-always-on;
262			};
263
264			vsnvs_reg: vsnvs {
265				regulator-min-microvolt = <1000000>;
266				regulator-max-microvolt = <3000000>;
267				regulator-boot-on;
268				regulator-always-on;
269			};
270		};
271	};
272
273	leds: led-controller@30 {
274		compatible = "ti,lp5562";
275		reg = <0x30>;
276		clock-mode = /bits/ 8 <1>;
277		#address-cells = <1>;
278		#size-cells = <0>;
279		status = "disabled";
280
281		multi-led@0 {
282			#address-cells = <1>;
283			#size-cells = <0>;
284			color = <LED_COLOR_ID_RGB>;
285			function = LED_FUNCTION_INDICATOR;
286
287			led@0 {
288				led-cur = /bits/ 8 <0x6e>;
289				max-cur = /bits/ 8 <0xc8>;
290				reg = <0>;
291				color = <LED_COLOR_ID_RED>;
292			};
293
294			led@1 {
295				led-cur = /bits/ 8 <0xbe>;
296				max-cur = /bits/ 8 <0xc8>;
297				reg = <1>;
298				color = <LED_COLOR_ID_GREEN>;
299			};
300
301			led@2 {
302				led-cur = /bits/ 8 <0xbe>;
303				max-cur = /bits/ 8 <0xc8>;
304				reg = <2>;
305				color = <LED_COLOR_ID_BLUE>;
306			};
307		};
308	};
309
310	eeprom@57 {
311		compatible = "atmel,24c128";
312		reg = <0x57>;
313		pagesize = <64>;
314	};
315
316	touchscreen: touchscreen@5c {
317		compatible = "pixcir,pixcir_tangoc";
318		reg = <0x5c>;
319		pinctrl-0 = <&pinctrl_touch>;
320		interrupt-parent = <&gpio4>;
321		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
322		attb-gpio = <&gpio4 5 GPIO_ACTIVE_HIGH>;
323		reset-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
324		touchscreen-size-x = <800>;
325		touchscreen-size-y = <480>;
326		status = "disabled";
327	};
328
329	rtc: rtc@68 {
330		compatible = "dallas,ds1341";
331		reg = <0x68>;
332	};
333};
334
335&i2c3 {
336	clock-frequency = <100000>;
337	pinctrl-names = "default";
338	pinctrl-0 = <&pinctrl_i2c3>;
339	status = "disabled";
340
341	oled_1309: oled@3c {
342		compatible = "solomon,ssd1309fb-i2c";
343		reg = <0x3c>;
344		solomon,height = <64>;
345		solomon,width = <128>;
346		solomon,page-offset = <0>;
347		solomon,segment-no-remap;
348		solomon,prechargep2 = <15>;
349		reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
350		vbat-supply = <&sw2_reg>;
351		status = "disabled";
352	};
353
354	oled_1305: oled@3d {
355		compatible = "solomon,ssd1305fb-i2c";
356		reg = <0x3d>;
357		solomon,height = <64>;
358		solomon,width = <128>;
359		solomon,page-offset = <0>;
360		solomon,col-offset = <4>;
361		solomon,prechargep2 = <15>;
362		reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
363		vbat-supply = <&sw2_reg>;
364		status = "disabled";
365	};
366
367	gpio_oled: gpio@41 {
368		compatible = "nxp,pca9536";
369		gpio-controller;
370		#gpio-cells = <2>;
371		reg = <0x41>;
372		vcc-supply = <&sw2_reg>;
373		status = "disabled";
374	};
375
376	touchkeys: keys@5a {
377		compatible = "fsl,mpr121-touchkey";
378		pinctrl-names = "default";
379		pinctrl-0 = <&pinctrl_touchkeys>;
380		reg = <0x5a>;
381		vdd-supply = <&sw2_reg>;
382		autorepeat;
383		linux,keycodes = <KEY_1>, <KEY_2>, <KEY_3>, <KEY_4>, <KEY_5>,
384				<KEY_6>, <KEY_7>, <KEY_8>, <KEY_9>,
385				<KEY_BACKSPACE>, <KEY_0>, <KEY_ENTER>;
386		poll-interval = <50>;
387		status = "disabled";
388	};
389};
390
391&iomuxc {
392	pinctrl_enet: enetgrp {
393		fsl,pins = <
394			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b020
395			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b020
396			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b020
397			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b020
398			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b020
399			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b020
400			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b020
401			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b020
402			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b020
403			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b020
404			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b020
405			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b020
406			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b020
407			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b020
408			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b010
409			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x1b010
410			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x1b098
411		>;
412	};
413
414	pinctrl_gpio_keys: gpiokeysgrp {
415		fsl,pins = <
416			MX6QDL_PAD_GPIO_0__GPIO1_IO00	0x1b0b0
417		>;
418	};
419
420	pinctrl_i2c2: i2c2grp {
421		fsl,pins = <
422			MX6QDL_PAD_KEY_COL3__I2C2_SCL	0x4001b899
423			MX6QDL_PAD_KEY_ROW3__I2C2_SDA	0x4001b899
424		>;
425	};
426
427	pinctrl_i2c3: i2c3grp {
428		fsl,pins = <
429			MX6QDL_PAD_GPIO_3__I2C3_SCL	0x4001b899
430			MX6QDL_PAD_GPIO_6__I2C3_SDA	0x4001b899
431		>;
432	};
433
434	pinctrl_ipu1: ipu1grp {
435		fsl,pins = <
436			MX6QDL_PAD_EIM_DA7__GPIO3_IO07                  0x1b0b0
437			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x10
438			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x10
439			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x10
440			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x10
441			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
442			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
443			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x10
444			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x10
445			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x10
446			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x10
447			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x10
448			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x10
449			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x10
450			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x10
451			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x10
452			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x10
453			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x10
454			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x10
455			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x10
456			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x10
457			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x10
458			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x10
459			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x10
460			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x10
461			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x10
462			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x10
463			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x10
464		>;
465	};
466
467	pinctrl_pmic: pmicgrp {
468		fsl,pins = <
469			MX6QDL_PAD_GPIO_18__GPIO7_IO13	0x1b098
470		>;
471	};
472
473	pinctrl_pwm1: pwm1grp {
474		fsl,pins = <
475			MX6QDL_PAD_GPIO_9__PWM1_OUT	0x8
476		>;
477	};
478
479	pinctrl_sound: soundgrp {
480		fsl,pins = <
481			MX6QDL_PAD_SD1_DAT0__GPIO1_IO16	0x1b0b0
482			MX6QDL_PAD_SD1_DAT1__PWM3_OUT	0x8
483		>;
484	};
485
486	pinctrl_touch: touchgrp {
487		fsl,pins = <
488			MX6QDL_PAD_GPIO_19__GPIO4_IO05	0x1b098
489			MX6QDL_PAD_GPIO_2__GPIO1_IO02	0x1b098
490		>;
491	};
492
493	pinctrl_touchkeys: touchkeysgrp {
494		fsl,pins = <
495			MX6QDL_PAD_GPIO_17__GPIO7_IO12	0x1b098
496			MX6QDL_PAD_GPIO_5__GPIO1_IO05	0x1b098
497		>;
498	};
499
500	pinctrl_uart1: uart1grp {
501		fsl,pins = <
502			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0a8
503			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0a8
504		>;
505	};
506
507	pinctrl_uart2: uart2grp {
508		fsl,pins = <
509			MX6QDL_PAD_GPIO_7__UART2_TX_DATA	0x1b098
510			MX6QDL_PAD_GPIO_8__UART2_RX_DATA	0x1b098
511		>;
512	};
513
514	pinctrl_usbh1: usbh1grp {
515		fsl,pins = <
516			MX6QDL_PAD_EIM_D30__USB_H1_OC	0x1b098
517		>;
518	};
519
520	pinctrl_usbh1_vbus: usbh1-vbusgrp {
521		fsl,pins = <
522			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29	0x98
523		>;
524	};
525
526	pinctrl_usbotg: usbotggrp {
527		fsl,pins = <
528			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x1b098
529			MX6QDL_PAD_EIM_D21__USB_OTG_OC		0x1b098
530		>;
531	};
532
533	pinctrl_usbotg_vbus: usbotg-vbusgrp {
534		fsl,pins = <
535			MX6QDL_PAD_EIM_D22__GPIO3_IO22	0x98
536		>;
537	};
538
539	pinctrl_usdhc4: usdhc4grp {
540		fsl,pins = <
541			MX6QDL_PAD_SD4_CMD__SD4_CMD	0x1f069
542			MX6QDL_PAD_SD4_CLK__SD4_CLK	0x10069
543			MX6QDL_PAD_SD4_DAT0__SD4_DATA0	0x17069
544			MX6QDL_PAD_SD4_DAT1__SD4_DATA1	0x17069
545			MX6QDL_PAD_SD4_DAT2__SD4_DATA2	0x17069
546			MX6QDL_PAD_SD4_DAT3__SD4_DATA3	0x17069
547			MX6QDL_PAD_SD4_DAT4__SD4_DATA4	0x17069
548			MX6QDL_PAD_SD4_DAT5__SD4_DATA5	0x17069
549			MX6QDL_PAD_SD4_DAT6__SD4_DATA6	0x17069
550			MX6QDL_PAD_SD4_DAT7__SD4_DATA7	0x17069
551		>;
552	};
553
554	pinctrl_wdog: wdoggrp {
555		fsl,pins = <
556			MX6QDL_PAD_GPIO_1__WDOG2_B	0x1b0b0
557		>;
558	};
559};
560
561&ipu1_di0_disp0 {
562	remote-endpoint = <&lcd_display_in>;
563};
564
565&pwm1 {
566	pinctrl-names = "default";
567	pinctrl-0 = <&pinctrl_pwm1>;
568	status = "disabled";
569};
570
571&pwm3 {
572	pinctrl-names = "default";
573	pinctrl-0 = <&pinctrl_sound>;
574	status = "disabled";
575};
576
577&uart1 {
578	pinctrl-names = "default";
579	pinctrl-0 = <&pinctrl_uart1>;
580	status = "okay";
581};
582
583&uart2 {
584	pinctrl-names = "default";
585	pinctrl-0 = <&pinctrl_uart2>;
586	status = "disabled";
587};
588
589&usbh1 {
590	pinctrl-names = "default";
591	pinctrl-0 = <&pinctrl_usbh1>;
592	vbus-supply = <&reg_usb_h1_vbus>;
593	over-current-active-low;
594	status = "disabled";
595};
596
597&usbotg {
598	pinctrl-names = "default";
599	pinctrl-0 = <&pinctrl_usbotg>;
600	vbus-supply = <&reg_usb_otg_vbus>;
601	over-current-active-low;
602	srp-disable;
603	hnp-disable;
604	adp-disable;
605	status = "okay";
606};
607
608&usbphy1 {
609	fsl,tx-d-cal = <106>;
610	status = "okay";
611};
612
613&usbphy2 {
614	fsl,tx-d-cal = <109>;
615	status = "disabled";
616};
617
618&usdhc4 {
619	pinctrl-names = "default";
620	pinctrl-0 = <&pinctrl_usdhc4>;
621	bus-width = <8>;
622	non-removable;
623	no-1-8-v;
624	keep-power-in-suspend;
625	vmmc-supply = <&sw2_reg>;
626	status = "okay";
627};
628
629&wdog1 {
630	status = "disabled";
631};
632
633&wdog2 {
634	pinctrl-names = "default";
635	pinctrl-0 = <&pinctrl_wdog>;
636	fsl,ext-reset-output;
637	status = "okay";
638};