i2c-mux-gpio.yaml

  1# SPDX-License-Identifier: GPL-2.0-only
  2%YAML 1.2
  3---
  4$id: http://devicetree.org/schemas/i2c/i2c-mux-gpio.yaml#
  5$schema: http://devicetree.org/meta-schemas/core.yaml#
  6
  7title: GPIO-based I2C Bus Mux
  8
  9maintainers:
 10  - Wolfram Sang <wsa@kernel.org>
 11
 12description: |
 13  This binding describes an I2C bus multiplexer that uses GPIOs to route the I2C signals.
 14
 15                                  +-----+  +-----+
 16                                  | dev |  | dev |
 17    +------------+                +-----+  +-----+
 18    | SoC        |                   |        |
 19    |            |          /--------+--------+
 20    |   +------+ |  +------+    child bus A, on GPIO value set to 0
 21    |   | I2C  |-|--| Mux  |
 22    |   +------+ |  +--+---+    child bus B, on GPIO value set to 1
 23    |            |     |    \----------+--------+--------+
 24    |   +------+ |     |               |        |        |
 25    |   | GPIO |-|-----+            +-----+  +-----+  +-----+
 26    |   +------+ |                  | dev |  | dev |  | dev |
 27    +------------+                  +-----+  +-----+  +-----+
 28
 29  For each I2C child node, an I2C child bus will be created. They will be numbered based on their
 30  order in the device tree.
 31
 32  Whenever an access is made to a device on a child bus, the value set in the relevant node's reg
 33  property will be output using the list of GPIOs, the first in the list holding the least-
 34  significant value.
 35
 36  If an idle state is defined, using the idle-state (optional) property, whenever an access is not
 37  being made to a device on a child bus, the GPIOs will be set according to the idle value.
 38
 39  If an idle state is not defined, the most recently used value will be left programmed into
 40  hardware whenever no access is being made to a device on a child bus.
 41
 42properties:
 43  compatible:
 44    const: i2c-mux-gpio
 45
 46  i2c-parent:
 47    description: phandle of the I2C bus that this multiplexer's master-side port is connected to
 48    $ref: /schemas/types.yaml#/definitions/phandle
 49
 50  mux-gpios:
 51    description: list of GPIOs used to control the muxer
 52    minItems: 1
 53    maxItems: 4  # Should be enough
 54
 55  idle-state:
 56    description: Value to set the muxer to when idle. When no value is given, it defaults to the
 57      last value used.
 58    $ref: /schemas/types.yaml#/definitions/uint32
 59
 60  settle-time-us:
 61    description: Delay to wait before doing any transfer when a new bus gets selected.
 62
 63allOf:
 64  - $ref: i2c-mux.yaml
 65
 66unevaluatedProperties: false
 67
 68required:
 69  - compatible
 70  - i2c-parent
 71  - mux-gpios
 72
 73examples:
 74  - |
 75    i2cmux {
 76      compatible = "i2c-mux-gpio";
 77      #address-cells = <1>;
 78      #size-cells = <0>;
 79      mux-gpios = <&gpio1 22 0>, <&gpio1 23 0>;
 80      i2c-parent = <&i2c1>;
 81
 82      i2c@1 {
 83        reg = <1>;
 84        #address-cells = <1>;
 85        #size-cells = <0>;
 86
 87        ssd1307: oled@3c {
 88          compatible = "solomon,ssd1307fb-i2c";
 89          reg = <0x3c>;
 90          pwms = <&pwm 4 3000>;
 91          reset-gpios = <&gpio2 7 1>;
 92        };
 93      };
 94
 95      i2c@3 {
 96        reg = <3>;
 97        #address-cells = <1>;
 98        #size-cells = <0>;
 99
100        pca9555: pca9555@20 {
101          compatible = "nxp,pca9555";
102          gpio-controller;
103          #gpio-cells = <2>;
104          reg = <0x20>;
105        };
106      };
107    };